Starwars problem

Russ J

Active member
vacBacker
Feedback
1 (100%)
Credits
233CR
Had a play on Starwars the yesterday then popped out for 1/4hr came back
for another go and the screen has gone blank ?? (the machine wasn't
turned off or anything inbetween plays) There's still power going to the
fan,marquee lights,coin mech lights but no sign of life on the
screen....(can't hear any sound from the speakers either....The red
lights on the PCB boards aren't lit up know though but the HV board is
lit up and the deflection board light is lit up...

I've been
reading through various threads on KLOV and i'm seeing a rough pattern
of it could be the ARII board ? (i don't have a mulitmeter to test
anything though)...I've read about this 'spot killer' but how do you
find out if it is that ? is there any visible sign's to look for on any
of the boards ?

I've posted this on DLF and Jamma+ as well just incase there's ppl that don't log on here
Russ J2012-08-17 21:10:53
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
As you've already worked out, the first place to start is with the power supply section. It sounds like the the cab power is OK, you have power to the lights, monitor, fan, etc so you need to look at the AR2 to see what it's doing. Get the multimeter and start measuring the voltages at the test points on the AR2. Put the black lead on the GND test point, and the red one on the other, they are all labelled what they should be. For + and - 5v use the +Sense and -Sense TP's. Report back what you have on all the voltages and we'll go from there.

Dan
 
  • Like
Reactions: trm

Russ J

Active member
vacBacker
Feedback
1 (100%)
Credits
233CR
cheers Dan & Olly,i've bought a multimeter from Maplin earlier,so i'll have a play about with it tomorrow (never used a meter before so not really sure how its used tbh
smiley9.gif
)

what's the 'GND' test point Dan ?

@Olly...the cab won't go into test mode at all mate like Dan said it powers up the rest of the cab but not the actual game itself (the red LED's don't turn on on any of the main PCB boards)

also this is the meter i bought earlier,

P8180065.jpg

P8180064.jpg


what 'settings' should i have it turned on to also which red socket do i plug the red lead into as there's 2 red sockets (i assume that the black lead goes into the black socket)
Russ J2012-08-18 00:09:12
 

Russ J

Active member
vacBacker
Feedback
1 (100%)
Credits
233CR
Think i may have sourced the problem...

One of the fuses on the Power Brick board has blown,

P8180061-1.jpg


P8180062-1.jpg


P8180063-1.jpg


I've tried the meter on it and there's no sign of life...all the rest of the fuses seem to check out ok
 

forcefulfil

EDOT King
vacBacker
Feedback
17 (100%)
Credits
1,675CR
yer check all your fuses first,then just meter the ar2 test points.
the ar2 is marked with all the voltage test points,Gnd,+5v.+12v etc etc

if you also download the schems for the ar2 it will also show you,the +5v can be adjusted to

all while the game is running

some machines dont boot/run correctly if the +5v is low etc

phil

forcefulfil2012-08-18 19:46:22
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
Here's some AR2 pics that show the test points for some voltages:

http://www.andysarcade.net/personal/tech/AR2mod.htm

There will be some for other voltages and some for GND.

Which fuse is it that's blow (location and value), it looks quite chunky so it's prolly a high ampage one? A fuse blowing isn't usually the source of a problem like this, it's the first symptom. It's possible that you just have a fuse that's the wrong specification or has just died but more likely that a short has developed somewhere causing the fuse to blow (as it should).

Dan
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
According to the schematics F3 is a feed to the bridge rectifier that is mounted in the power brick and ultimately generates the +5v. So... if you replace the fuse again and it blows I would test that bridge rectifier or unplug the big connector on the power brick (the 15 pin one looking at the schematics). Obviously there are mains voltages floating around on that power 'brick' so I'd power it off first
smiley18.gif
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
Yep, the 35A BR would be my prime suspect too. You can remove it and test it with the diode test on your multimeter (make sure you note which connector goes where!). You can get the fuses and BR at RS if you need a source.

Dan
 

Russ J

Active member
vacBacker
Feedback
1 (100%)
Credits
233CR
I got some fuses today through the post and replaced the buggers fuse and the game fires up ok know
smiley4.gif
smiley4.gif
smiley4.gif
but i'll keep an eye on the Bridge Rectifier (tbh a few ppl have mentioned this but i've only just found out what it was by looking at the manuel
smiley9.gif
) its located 'underneath the actual fuse 'tray' isn't it....now i see by the diagram its held on by a nut/bolt,now if i need to test this how do i test this (not looked underneath the actual power brick 'tray' tbh...i assume there's a wire going to the part ? (only going by what it looks like in the manual)

also with you saying 35A Dan has the Rectifier got a fuse attached to it (sorry to sound thick
smiley9.gif
)
Russ J2012-08-21 20:41:17
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
How to test a BR:


you'll see 4 tabs. AC input on 2, DC output on 2. The DC output is fused at F3.

Edit: The video is for a Defender power supply, but the principle is exactly the same. Swapping one out on a Starwars would be a trivial job.tb lilley2012-08-21 20:50:03
 
Top