strange interference

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR
Hi there, ive got a Nanao Ms-2932 monitor connected to a pc and im getting some weird interference...





cant quite catch it properly on my camera....but its like wavy lines...

ive tried a different vga cable, power supply....

any ideas?
 

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR

managed to catch a bit of it ,around the 50 second mark you can just catch the interference or what ever it is on the left side of the screen...this is all over the screen and starting to bug me....you cant see it all the time but its there....
 

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR
i made sure the cables were out of the way...also disconnected the motor feed to make sure it wasnt that..

i think the next thing ill try is with only the monitor powered up with another source....may have to nick my brothers laptop for that....
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
terminator2k2 said:
big10p said:
Have you checked the VGA cables you've tried are fully wired?

never gave that a thought....why would it be any different...?

ill go and have a read upon that now....

I was getting screen interference (grounding issue) until I swapped the cheapo cable that came with my JPAC for a decent, fully wired one. Think only the main GND in the cable was wired up, but not the individual RGB return GNDs, or something. Are you using a JPAC at all. Not saying this is definitely the issue, but might be worth checking just to rule it out...
 

Vamino

Insert coin(s)
vacBacker
Feedback
23 (100%)
Credits
2,698CR
Just seen this.

In my line of work when old CRT screens die we replace them with an LCD screen, sometimes the existing cables are long enough to reach the new LCD panel, and sometimes not. When they don't reach I use a cheap 99p connector off ebay that links 2 cables together and that introduces interference, I get swirling interference on the screen. If the customer complains then we replace the cable with a decent one and the issue goes away.

Cheap cables and adaptors usually cause some issues if the cables are low quality. Personally, for my mame driver build I'll be using a shielded cable that plugs straight into the GPU without the need for one of those DVI-I - VGA adaptors.

I'm not saying removing adaptors will solve your problem but along with the other guys suggestions it should hopefully reduce the issues you are experiencing.
 

obcd

Active member
Credits
3,830CR
I assume with DVI - VGA you mean the passive adapter piece that plugs in the DVI connector and has the subd vga connector on the other end. A good vga cable uses 3 75ohms coax cables to transport the 3 color signals. It's usually pretty thick and stiff due to that. If your pc is below the seat, you need a rather long vga cable to connect it, so a good quality cable might not be a bad idea. I am unsure if an active "dvi 2 vga" adapter would cause some delays. If not, it might be another possible way to connect your screen to your pc. But, you should try to pinpoint what causes the issue, and the first logical step is connecting another video source. After that, connect it using the same video cable. Maybe a thick ground wire running from your pc case to your monitor chassis can make a difference. Interference is most of the time a bitch to solve.
 

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR
ok so far ive tried:

turning off everything except the pc and monitor - fault remains

3 more vga cables - all give the same fault

ive tried from my laptop using different vga cables and running them outside the cab - fault remains

So was about to give up for the night and with just a vga cable plugged in to the chaasis, not connected to anything - the fault was there on the screen.

so tried another cable same as above - fault was there

so I disconnected the plug from the chassis and turned the brightness up and fault was there again.....

I uploaded a video to youtube....may be better viewing in full screen so you can see the wavy lines....

 

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR
Hurray Banana said:
Can't make out much but might be interference. Have you got a fridge nearby (or some other motor based device) or a neighbour into radio ham

no none of them....

I unplugged the d-sub connector from the chassis and got this interference....

plugged back in without the pc vga cable connected and black screen , no interference.

plug any vga cable in, connected to pc or not and interference is back again....

I was trying to eliminate if the chassis it self is giving me the problem, but now im even more confused.....as why is the interference their when I unplug the dsub connector.....
 

obcd

Active member
Credits
3,830CR
Maybe you have an unstable voltage somewhere around the rgb amplifier. Or there is some bandwith limiting circuit that isn't doing it's job so that all interference becomes visible. I know there exist subd connectors with buildin ferrit rings. No idea what is used on that Nanao. If you terminate the video input's with 75 ohms, does the interference go away? Maybe the inputs became high impedance for wathever reason and pick up spurious easier due to that.
 

terminator2k2

Active member
Feedback
1 (100%)
Credits
327CR
This was doing me nut in yet again today
smiley19.gif


so tried another transformer, removed speakers, all cabling from around the tube, new vga cable....problem still there....

removed the dsub connector from its housing and moved it around to see if it got worse/better....no joy

so I was looking at the chassis and theres a arrow by a screw hole with no screw in it right by the dsub connector....so decided to put one in as I know if theres arrow by a hole , it usualy means a screw was there...

and it cured the blummin interference....took it back out, interference back......

and no not the big arrow I put on the pic lol

terminator2k22016-05-28 16:30:18
 
Top