SYSTEM16 Jamma adapter replacement

sapporo46

User
Feedback
2 (100%)
Credits
70CR
Hi, anybody know of a good place to source one of these?

Managed to blow mine up recently
smiley5.gif


I've had a look but thought there might be somebody on here or similar (not being lazy!)
 

VectorGlow

Active member
vacBacker
Feedback
34 (100%)
Credits
900CR
sapporo46 said:
Hi, anybody know of a good place to source one of these?

Managed to blow mine up recently
smiley5.gif


I've had a look but thought there might be somebody on here or similar (not being lazy!)

In what way have you blown it up? I assume it's just a few fried tracks and if so they should be pretty easy to repair.

Can you upload a picture of the damaged adapter (both sides of it)?
 

Ace`

PlanB contributor #1
Feedback
40 (100%)
Credits
4,038CR
Is that a burn mark on the M in the Jamma text? if the big trace from pin 5 to 6 is alright your problem is with the game pcb.
 

VectorGlow

Active member
vacBacker
Feedback
34 (100%)
Credits
900CR
Ace` said:
Is that a burn mark on the M in the Jamma text? if the big trace from pin 5 to 6 is alright your problem is with the game pcb.

Hard to make it out, but it just looks like a thru-hole.

@sapporo46 - I'm half asleep right now but on looking at the pics I can't see any obvious physical damage. Can you check that the board is getting the required voltages, particularly +5 volts and +12 volts DC?

If it is then you may well have a board problem.

I guess that the game isn't playing blind? (ie sound but no video)?
 

vectrex

User
Feedback
9 (100%)
Credits
47CR
I had a look at my adapter:



It really seems to be a burnt trace in the +12V line on your adapter. The thru-hole is further down ...

vectrex2016-10-05 15:10:16
 

VectorGlow

Active member
vacBacker
Feedback
34 (100%)
Credits
900CR
Agreed, with the slightly better quality photo and vectrex's example for comparison it does look like the +12v track is damaged. It would also explain the lack of sound.

Fixing the burned out track is trivial, what what really needs to be figured out is why the track blew out. Could be a board fault but could even be an issue with the PSU or even the wiring, connector, etc.
 

Bensonrad

STILL looking for an Outrun & Paperboy!
vacBacker
Feedback
68 (100%)
Credits
940CR
What PCB is the game?
just thinking it might be sega 16 game with a battery on it, some of the earlier ones if suicided lose sound but still play.Bensonrad2016-10-09 10:45:13
 

vectrex

User
Feedback
9 (100%)
Credits
47CR
It's a Shinobi PCB which he bought from me. It's a bootleg so the missing sound can't be a suicide issue.

He said he connected the adapter the wrong way ...

Just take a DMM and measure the voltage between pin 1 and 5 of the adapter (parts side heading towards PCB):

- if +12V is present there has to be another problem

- if no +12V is present run a jumper wire from pin 6 of the adapter (parts side heading towards JAMMA connector) to pin 5 of the adapter (parts side heading towards PCB)

The whole procedure only takes about 10 minutes ...
 

sapporo46

User
Feedback
2 (100%)
Credits
70CR
So after buying a multimeter that actually worked, I tested the voltages and all +5V/+12V are OK. +12 reads at 12.84, +5 reads at 4.59 on the adapter, closer to 5 on the supergun.

Tested on the adapter pins, the PCB pins and the Supergun pins (pic here).

The supergun is definitely OK as it plays other JAMMA boards without any problem. The volume pot on the game PCB is a bit crooked but not loose at all.

Erm...
smiley6.gif
 

vectrex

User
Feedback
9 (100%)
Credits
47CR
You could try to increase the 4.59 volts a little bit and see if it changes anything.

But in one of your first mails to me you said that when you first connected the pcb there were a pop and a spark and that you think that you connected the adapter the wrong way.

So I assume that you have fried some component on the pcb itself ...
 
Top