test switch wiring

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
Need a bit of advice please

I have a jamma cabinet without a test switch, if I wish to wire one in am I correct in thinking that i need to wire one side of the switch to pin 15 on parts side of jamma loom connector and the other side of the switch to any ground?

reason being i have a couple of CPS2 games where the test switch does not work on the board.

thanks in advance

regards

sean

seanr282015-01-07 17:02:07
 

phillv85

Active member
Feedback
8 (100%)
Credits
490CR
Yup
smiley1.gif
 

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
a bit more info, using my multimeter with no pcb connected to the loom, between pin 15 and gnd I have no continuity which i would expect, however, when a pcb is connected to the loom (any pcb) I have continuity between pin15 and gnd....

why is this??
 

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
they don't, but when any board / PCB is connected they do, therefore my test switch does nothing when connected.

so what am I am doing wrong? how do i get the test switch to function please?
 

favouredson

Super Star
vacBacker
Credits
1,260CR
How about a bit more info...

What type of switch have you used?
(It needs to be a momentary action one)

How have you connected it?

(If you used a standard micro switch button have you connected the NC terminal instead of the NO one?)

We are not psychic.

(Most of us, anyhow.)
 

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
ok i have used a momentary type switch.



but the switch doesn't appear to do anything when connected, because as soon as any pcb is connected pin 15 becomes grounded.




What am I missing?




my understanding is that you connect one side of the switch to pin 15 and the other side to a common ground and that pin 15 would only become grounded when the button is switch is pressed?

seanr282015-01-08 23:03:00
 

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
Purity said:
What game are you trying this on?

I have tried this on robocop 1 and 2, and many cps2 titles, but as i say, as the ground becomes connected as soon as any board is connected to the jamma loom, the switch isn't going to do anything anyway.

seanr282015-01-08 23:14:43
 

retrorepair

Active member
vacBacker
Feedback
26 (93%)
Credits
378CR
IIRC Robocop 1 and 2 don't have a test menu accessible from the test switch. As for your CPS2 mobo, if the button doesn't work on the mobo then it may be that input is faulty so likely won't work from the switch either. If you have a Neo Geo try that.

As for the switch, make sure pin 15 (on the top, next to video ground) is connected to one side of the switch and ground is connected to the center pin.
 

seanr28

Active member
Feedback
9 (100%)
Credits
319CR
retrorepair said:
IIRC Robocop 1 and 2 don't have a test menu accessible from the test switch. As for your CPS2 mobo, if the button doesn't work on the mobo then it may be that input is faulty so likely won't work from the switch either. If you have a Neo Geo try that.

As for the switch, make sure pin 15 (on the top, next to video ground) is connected to one side of the switch and ground is connected to the center pin.

its a 2 pin switch, so one side goes to ground and the other to pin 15, I don't have any negeo to test, but as pin15 is grounded as soon as a pcb is plugged in I cant see it working???
 

retrorepair

Active member
vacBacker
Feedback
26 (93%)
Credits
378CR
Are you metering at the JAMMA edge? Disconnect your wire and see what happens. Definitely looking at the top of the JAMMA connector, not the bottom? Does it connect ground just on the CPS2 board or all boards?
 
Top