Wonder empty cab help

Silverhawk

Newbie
vacBacker
Credits
8CR
I have a gutted wonder boy that needs everything pretty much.

Going step by step I need a suitable monitor for it. And a replacement bezel/screen are needed, no idea where to get them.

The other next point is a replacement glass for the control panel. The game of one is too dark and also scratched damaged.

Where the monitor was has holes about 21” diagonally and 19” across.Silverhawk2017-12-10 22:32:17
 

Silverhawk

Newbie
vacBacker
Credits
8CR
This the panel that needs a need glass plexiglass front

9AE85D64-2C19-4F9D-894A-266BA32EC727.jpeg
 

Flinnster

The Dino King
vacBacker
Feedback
29 (100%)
Credits
2,566CR
OK because your panel has the bit of metal in front holding it in place, wood on either side + monitor at the back it's not like you'll need pristine showroom edges on the plexi.
Get your measurements sorted and pop down to your local B+Q. They'll sell plexi in sheets, 2mm or 3mm should be totally fine for covering that.
Get them to cut it for you to match the CP size, that way if they do crack it while sawing, it's their fault
smiley2.gif


Then you only have to worry about drilling the button holes. I've never actually done it on plexi yet, so I'll let someone with experience advise on that. Step drill approach like doing button holes in metals folks?

Also I think on my cab I have the buttons the other way round (yours are the 'correct' Wonderboy CP arrangement in the arcade manual though).

Shame the right hand side of your instruction strip is missing. Other than that the CP looks very cleanable and in good nick.
Flinnster2017-12-11 01:25:16
 

strykr

Active member
vacBacker
Feedback
11 (100%)
Credits
1,351CR
adding to what Flinster said, might be easier measuring up and contacting trent plastics to cut your plexi, they charge per hole but for the extra few quid its worth it, ive never had much luck pillar drilling plexi myself.

whats wrong with the monitor in the cab currently? Far easier to contact gunblade or tb2000 on here to get it repaired then try to find a replacement.

im glad your keeping it a Wonderboy, it may have been a conversion kit but imo they are just as much a part of arcade history as dedicated cabs and worth preserving
smiley1.gif
 

Flinnster

The Dino King
vacBacker
Feedback
29 (100%)
Credits
2,566CR
strykr said:
whats wrong with the monitor in the cab currently? Far easier to contact gunblade or tb2000 on here to get it repaired then try to find a replacement.

He got an empty shell black cab (needs full restrore), but it had the WB CP and marquee.
Everything else needs adding.
 

Silverhawk

Newbie
vacBacker
Credits
8CR
BTW is there any massive difference in play between a bootleg and original wonderboy pcb? And apart from pandora and mame is there any other options to get it rigged up cheap? Are superguns an option?
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,091CR
Don't think it plays well on any multiboard. I've played it on the game elf and it has hideous screen tearing and choppy scrolling, due to the display not being vsync'd. On the other hand, it plays great on GroovyMAME.
big10p2017-12-14 22:16:36
 

Flinnster

The Dino King
vacBacker
Feedback
29 (100%)
Credits
2,566CR
Yep so I have it running on a pi via AdvanceMame currently without scroll-tearing and at near 1:1 pixel aspect ratio.
It's okkkaaay, but still not a patch on real hardware in my view. But I might be possibly a tad biased
smiley36.gif

I'm still holding out for an original if I can ever get hold of one at below spare-kidney prices (I run a bootleg in my dedicated cab).

Bootlegs are close to be honest. I don't think there's a bootleg in existence for the 'Deluxe' romset though.
Flinnster2017-12-14 23:21:26
 

Flinnster

The Dino King
vacBacker
Feedback
29 (100%)
Credits
2,566CR
Not a lot really, although the hardware Wonderboy is on varies immensely.

My bad. It turns out 'deluxe' was just another bootleg (and yet the version I probably played the most!).
It appears a hack was added to alter the speed the energy decreases at. Slow/Fast are the settings. Mame lists the dip switch as 'unused' on the other versions.

For years I thought only 'deluxe' had the hidden 'E' 'S' 'C' letters and hidden lives. But nope, they are in all versions.
 

Silverhawk

Newbie
vacBacker
Credits
8CR
Still progressing with this. Any ideas on removing the glue/residue on the small metal panels?

Ive tried bleach wipes etc but its not coming off and I don't want to risk damaging the marquee...

There are also dirt marks on the panel art but again not sure what to use without damaging it..

arcades.jpg
 

Flinnster

The Dino King
vacBacker
Feedback
29 (100%)
Credits
2,566CR
Magic Eraser is slightly abrasive, so while it'll get rid of residue, it can scratch, or take the gloss sheen off paintwork.

If it genuinely is glue residue, I'd try isoprop alcohol or a little white vinegar first - try rubbing it with a q-tip / earbud, not rubbing with a large cloth soaked in the stuff.
 

bomjac

Active member
Feedback
3 (100%)
Credits
453CR
+1 for Isopropyl (aka prop-1-ol) - Its what sign companies use for cleaning prior to applying their vinyl etc.

I used it on my Sinistar to remove the residue from the Konami Baseball side art residue and Marquee that had been used. Also on the CP to remove the glue from the CP that had been applied. It came off eventually with a lot of rubbing. Thankfully they had reversed the original marquee before the Baseball art was applied to it.

If you really, really want the 100% best solution available - maybe Muddymusic could scan the artwork and reverse print a brand new perspex.

https://www.arcadeartshop.com/

bomjac2017-12-17 15:34:58
 

martin8or

Newbie
Feedback
1 (100%)
Credits
144CR
If it's a tacky type glue then you can soak some wd40 on it and leave it a while, then use a cotton bud with some wd on it to get it off. If it's a dry type glue like a layer of enamel then I'm not sure what you can use.
 

Silverhawk

Newbie
vacBacker
Credits
8CR
It looks like some kind of sediment between the plexiglass and the panel. I’ve tried scratching some of it off but it’s rock solid. Nothing I’ve tried can get the stains off .. looks like a type of powerful glue that kept everything in place
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,091CR
If all else fails, Novus plastic polish should shift it. I'd start by trying Novus 2, but if that's not strong enough, go with Novus 3, then 2 and 1 for final polish.
 
Top