World Rally PCB?

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
this is a mate's game. it boots up with a white screen and flashes of corrupt graphics. the longer you leave it on for the better it gets, but it never get's 100%
I replaced a couple of the bigger caps as that was something simple I could try, but it's not made a difference.

anyone seen this sort of thing before?
I do have a logic probe, but have never used it :)
 

ben76

Hunts Spies
Feedback
7 (100%)
Credits
1,136CR
http://www.arcadecollecting.com/dead/

Yep it is looks like its fecked mate
smiley18.gif


- Ben
 

Fuzzy

Active member
vacBacker
Feedback
18 (100%)
Credits
564CR
I have this PCB and occasionally I've had to reseat the socketed chips otherwise I get the same sort of screen you've mentioned above.
 

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
it has two socketed chips which I tried reseating already
the legs looked clean. No corrosion. So all I did was take them out and pop them back in
 

Fuzzy

Active member
vacBacker
Feedback
18 (100%)
Credits
564CR
JohnnyChaos said:
it has two socketed chips which I tried reseating already
the legs looked clean. No corrosion. So all I did was take them out and pop them back in

That's what I did. I remember trying it a few times without success, and having to press down on the chips very hard to get them to work.

Fuzzy2014-01-04 19:32:04
 

enricnes

Newbie
Credits
8CR
Hi Guys,
Gaelco released the code to program again the Dallas microcontroller. There's a spanish post showing how to do that. Will look for it and translate it here.
Cheers
 

Fuzzy

Active member
vacBacker
Feedback
18 (100%)
Credits
564CR
enricnes said:
Hi Guys,
Gaelco released the code to program again the Dallas microcontroller. There's a spanish post showing how to do that. Will look for it and translate it here.
Cheers

smiley20.gif
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,009CR
I was sent this ages ago, probably by IronGiant / Vectorglow

WORLD RALLY SECURITY PROCESSOR RELOAD

Usual disclaimer if you try this and hurt yourself destroy your board kill your cat etc etc your problem...

First off confirm that when your game is booted up it displays COPROCESSOR NOT READY in red in the boot up diagnostics screen and should stay displaying this until the game is coined then the game should appear to start up normally start the game then crash the car into something at this point the graphics should go wonky and the car will be placed back on the screen outside the normal background making the game unplayable. If this happens then the security processor has most likely suicided and needs to be reloaded if not then It is most probably ok and the fault is elsewhere.

Things required to reload processor

1. A computer with a serial port
2. Some kind of rs232 to ttl interface something based around one of the many max chips would be ideal
3. The wrdallas.bin file from the world rally US mame ROM set and a way of converting it to Intel format
4. A CR2032 lithium coin cell with suitable tabs attached

Now to start

1. Carefully remove the black plastic cover in the centre of the PCB the one that has do not open written next to it on the PCB. Be very careful, as there are smd parts and fine tracks just under the edges and try not to break the cover.

2. Under the cover you will find a battery and a 5 pin connector first test the battery if the battery is over 3V then the secure processor is most likely ok look elsewhere for faults first if less than 3V remove and replace the battery with a new one.
NOTE if the processor wasn't already dead this will kill it.

3. Make up a lead to connect your RS232 to ttl interface to the PCB connections to the PCB are

o pin5 =GND
o pin4 =PROG
o pin3 =TXD
o pin2 =RXD
o pin1 =+5V

Pin1 is marked by a white dot on the PCB closest to the edge connector end of the PCB pin4 the prog pin will need to be connected to gnd through a switch.

4. Connect the board to your cabinet or test rig then connect your computer and interface power every thing up start HyperTerminal on your computer with the settings 2400 N 8 1 select xon xoff handshaking.

5. Turn on the switch connected to pin4 the prog pin to gnd it then send a to the board if all is well it will return the following [DS5002 LOADER VERSION X.X COPYRIGHT (c) XXX DALLAS SEMICONDUCTOR ]
next send U the response should be [UNLOCKED].

6. Open notepad load your converted wrdallas.bin file highlight all the text and copy it to the clipboard go back to HyperTerminal send L the processor should return a prompt now paste your copied file into HyperTerminal then wait for a second prompt to appear below the first be patient it takes about 10 minutes.

7. At this point the processor has been reloaded and reset out of boot loader mode also the game has most likely rebooted and should be working correctly now switch off the prog switch then switch it back on send wait for the boot loader message and prompt then send Z processor will return [LOCKED] this resecures the processor.

8. Now turn off the prog switch then the power to the game disconnect the programming lead from the board power the board back up and confirm the boot up diagnostics menu shows COPROCESSOR OK in blue followed by the game starting attract mode coin up start and check the game plays correctly.

9. If all is now working correctly refit the plastic cover use a dab of ca glue to secure if necessary.

Hopefully this makes some kind of sense to someone and you now have a working world rally board any questions queries help give me a yell.
 
  • Like
Reactions: trm

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
thanks for that.
Unfortunately that says it needs to boot up and coin up. But like I said it it boots to a white screen with flashes of corrupt graphics so sounds different doesn't it?
 

ben76

Hunts Spies
Feedback
7 (100%)
Credits
1,136CR
JohnnyChaos said:
thanks for that.
Unfortunately that says it needs to boot up and coin up. But like I said it it boots to a white screen with flashes of corrupt graphics so sounds different doesn't it?
I don't think yours has suicided mate
 

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
tried reseating the socketed chips again and reflowed their solder, but still the same. my mate's taking it back now.

but thanks to everyone for the suggestions :)
 
Top