Asteroids sound problem

minwah

Active member
Feedback
3 (100%)
Credits
238CR
Evening all,

I recently bought pooman's Asteroids cabaret machine. I've been doing some cosmetic work to it, and at the weekend finally got round to replacing the PCB edge connector as recommended by pooman...

So plucked up the courage to plug it in and fire it up yesterday. Initially no picture, but the game was playing. I could make out the picture collapsed up at the top of the screen, but waited for a minute or two and the picture gradually started filling the screen, with some glitches, but finally seemed to be ok. The only niggle I can see is that the lines which build the main ship look a bit 'wobbly' at certain angles...I don't know if this is to be expected on an old machine? I haven't played on an Asteroids for 10+ years!

So aside from that the game seems to play fine, except for quite a loud humming sound through the speaker. It is not there with the volume turned right down or very very low.

I fired it up again tonight and no video problems (bar the wobbly ship) but after a while the humming sound got louder and the game sounds are not right, barely audible and just don't sound right.

I've done a search and found that it could be numerous things, but could anyone suggest where to start? Capacitors?

Any advise would be much appreciated!
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
forcefulfil said:
Have you confirmed you have an accurate +5v @ the pcb itself not the ar1?

No...it was 5.25v at the AR board without the PCB connected which I thought was about right. I'll check it on the PCB.

Thanks!
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Usually it is recommended to make a jumper lead between the AR test points and the PCB test points for +5 and GND if you have a dodgy edge connector, helps to prevent humming, and frying the PCB

but if you've replaced the edge connector......
smiley5.gif

Purity2013-07-22 22:30:45
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
It's 5.07v on the PCB...is that close enough?

Now the hum is about back to how it was, and the game sounds are almost back to normal, except the explosion sounds like a clap of thunder (ironically given the weather!).
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
Purity said:
Usually it is recommended to make a jumper lead between the AR test points and the PCB test points for +5 and GND if you have a dodgy edge connector, helps to prevent humming, and frying the PCB

The PCB edge looks good as well, but I suppose it's a good idea anyway to add the jumper leads. I'll do that tomorrow!
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
So having waited a day and fired it up again, the hum is still there but not too bad, but the sounds are not quite right...hard to explain but quite tinny as if a filter is applied to the sound. Not sure if something has broken or if there is a problem causing this...

I decided to check the voltages at the PSU and have some strange results for the AC:

Pin 6 & 7: 3.44VAC (should be 36VAC)
Pin 8 & 9: 12.10VAC (should be 6.3VAC)
Pin 11 & 13: 17.6VAC (should be 65VAC)

These are very odd, I don't really believe these are correct and think it is something to do with my multimeter...ie I don't think the monitor would be working with such low voltage. It's a 20 year old multimeter but it's digital and auto-ranging - never had a problem before.

So I measured each pin to GND (pin 15) as well:

Pin 6: 30.5VAC
Pin 7: 24.8VAC

Pin 8: 23.5VAC
Pin 9: 13.78VAC

Pin 11: 67.6VAC
Pin 13: 42.6VAC

These seem to make more sense...but still don't look quite right. If Pin 6 & 7 should measure 36VAC, then am I right in saying pin 6 to GND and pin 7 to GND should both read 18VAC? And similarly for the other pins (pin to GND = hi pin to low pin / 2)?

Bit confused...don't think I will fire the machine up again until I work this out. Iffy transformer or iffy bloke measuring voltages?!
 

pooman2084

Be Attitude For Gains!
vacBacker
Feedback
26 (100%)
Credits
1,886CR
Glad to read that it's up and running!
smiley20.gif
Good work!

I never had any audio issues, apart from a slight hum. I was hoping the new edge connector would solve that for you.

There are a few vector experts on here, so hopefully they can chime in with some ideas.
 

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Have you definitely got a good battery in your test meter? You'll get screwy voltage measurements if it's going flat.
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
trm said:
Have you definitely got a good battery in your test meter? You'll get screwy voltage measurements if it's going flat.

I'll try some new ones just in case, but I'm getting expected readings for DC volts, and I recently tested something on mains AC and got the right reading so would be surprised if it is that.
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
pooman2084 said:
What happens when you go into test mode? Is the picture correct there?

Yes it looks fine in test mode, no warning beeps.

Have a good read here:

http://arcarc.xmission.com/Tech/Asteroid%20Tech/asteroidsrepair.html

lots of good Asteroids repair logs

Thanks, few things I can try there. I think I will try to get to the bottom of whether my AC voltages are ok before I go any further though. Seems odd that everything pretty much works ok...after trying some new batteries perhaps I should try a different multimeter!
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Please don't just blindly try a bunch of stuff out of that document. That's been around for donkeys years and to be honest, while I'll admit there are some good things in there, I wish it would just die a death really as there's also a lot of stuff in there that is just completely random!!

Take for instance under the section of sound hum. It suggests replacing the power supply with a switcher and putting a bigger / better amp in. WTF???!!! How random is that! If you put a switcher in, you won't have all the voltages you need and frankly, that's a nonsense suggestion. And a bigger / better amp?? Why??

Hum, is mostly likely going to be caused by either noise on the voltages or poor grounding. Probably the latter.

Have you tried adding good quality, fairly thick jumper wires between a GND test point on the AR PCB and a ground test point on the game PCB. Also repeat for 5v test points too. You should be able to do this with spade connectors if you want it to be reversible. 9 times out of 10 that greatly reduces the hum to a point you'll be happy enough. Then there are some electrolytic capacitors that can be changed both on the AR PCB and the game PCB if you're still not happy.

That Asteroids document is fine if you know enough about what you're doing to be able to trawl through it and sort the wheat from the chaff. If you aren't experienced enough for that then you'd be better off working with us to get it solved
smiley4.gif
 
  • Like
Reactions: trm

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Incidentally, having just re-read the first post, I'm now doubly convinced the wobbly vectors are either noise or grounding as per my post.
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
I haven't tried the jumper wires yet, but will do that tonight and see what happens...

I did wonder about the Asteroids Encyclopedia, I saw the 'switcher' part and it also refers to video BIP pot adjustment, which I don't believe Asteroids actually has.

Many thanks for your help!
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
No worries. I don't mean to knock it too much. I'm sure there IS some decent info in there but as you've found with the BIP pots, there's a bunch of tosh in there too
smiley36.gif


It did occur to me that you may not know what I'm on about with the jumper wires. If you need any detail let us know. Tonight only I could take a pic of the inside of mine if you need, but I'm away from the morning for a bit.
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
guddler said:
It did occur to me that you may not know what I'm on about with the jumper wires. If you need any detail let us know. Tonight only I could take a pic of the inside of mine if you need, but I'm away from the morning for a bit.

It's ok I know what you mean. I've added one for the GND and 5V. Not sure there is any difference but to be fair the hum is not bad at all when first switched on.

So what happens at the moment is...turn on, it plays fine but the sounds are a bit off. After a few minutes, a really nasty buzz sort of builds up - I am guessing as something warms up? It sounds bad so I turn it off at this point...I'm a bit worried that the first time it happened it damaged something which is why the sounds are now not quite right.

Anyway I did a sound recording which is worth a thousand words. You will hear that the sounds are not quite right. About half way through the recording, the nasty buzz starts happening, and gets worse. The machine had been on for 2 minutes when the buzz starts.

http://mamewah.mameworld.info/downloads/asteroids.mp3
 

minwah

Active member
Feedback
3 (100%)
Credits
238CR
guddler said:
Incidentally, having just re-read the first post, I'm now doubly convinced the wobbly vectors are either noise or grounding as per my post.

I just thought I should clarify that 'wobbly' may not have been a good description. Most of the vectors look absolutely fine. It is when the ship is at certain angles (ie not dead straight up/down/left/right), the lines that build the ship are not dead straight lines as you would expect. The lines are soft of jagged, almost like you get on a raster screen when drawing a diagonal line.

I tried to take a picture but I can't get it to come out well enough. However it looks a bit like this:

http://www.melchman.net/arcade/files/vector.jpg

I will stress again that the other vectors look fine. I'm not sure if it has to do with that the ship appears to have thicker or brighter lines than most other objects.
 
Top