Atari power brick

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Hmmm I'm getting 0.7V DC out of an Atari power brick rather than 10-15V.
Big blue has been switched with one from a good supply and the rectifier passes

all 4 diode tests in both directions (~0.5V drop or open as expected).

I guess some transformer coils have packed up. The AC voltages are fine.

A get a low resistance through the suspect coil and I couldn't detect

any shorts between coils.

Any ideas what else to try?

Are these still tricky to get replacements for (this one is for a 60V monitor)?
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
As above. In particular see what AC is being fed into the rectifier (usually the 2 orange wires). Both of those wires are usually fused - so check fuse holders are tight / free from corrosion.

Agree the bricks rarely go wrong - but I have seen a knackered one before.

If you do need a new one - just about any Atari brick from that era will output 60VAC, inc raster cabs.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Here is how was taking the measurement.
voltmeter on 20V DC, interlocks pulled out.

The fuses are intact, but the fuse holders are pretty corroded and I've seen a spark

or two near them.

IMG_2017.JPG
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
You can get a new fuse block strip and fuses for Atari bricks online now.

Quite a few online shops so it like www.arcadeshop.com
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Battlezone said:
Here is how was taking the measurement.
voltmeter on 20V DC, interlocks pulled out.

The fuses are intact, but the fuse holders are pretty corroded and I've seen a spark

or two near them.

IMG_2017.JPG

Probably a stupid question, but you do have the DMM switched to DC right?

What happpens if you move the Red probe to pins 1 and 2? (Keeping Black Probe where it is?)
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Another thing, what's this missing fuse nonsense? You have no leads running to the row either. There's your problem right there.

That fuse block is a can of worms, F3 section is showing considerable burn.
Equites2016-03-14 20:08:12
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Can only repeat my advice above - rather than measure the DC, first find out whether the transformer is sending AC to the rectifier. 2 orange wires from the transformer go to a corner each of the rectifier. Set meter to AC, flip the brick on its side, one lead to one orange corner, other to other orange corner.
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Equites said:
Another thing, whats this missing fuse nonsense?  You have no leads running to the row either.  There's your problem right there.

Not always Nad. The AC for the rectifier is usually fused at F2 and F3. But not always. E.g a Battlezone brick skips F2, with only F3 fused.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Yup the DMM is on DC. Pins 1-3 all read the same. I guess I'll swap out the fuse
strip in any case.

The two orange wires feeding into the rectifier read 0V AC but that could be

fuses again. I better check the wires too I guess.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
tb lilley said:
Equites said:
Another thing, whats this missing fuse nonsense? You have no leads running to the row either. There's your problem right there.

Not always Nad. The AC for the rectifier is usually fused at F2 and F3. But not always. E.g a Battlezone brick skips F2, with only F3 fused.

Interesting, I just compared the Asteroids brick (which I used for reference initially) and you are right, the Battlezone brick skips F2. Quite different.

Even an old dog like me learn's something new every day.

Equites2016-03-14 20:15:45
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
I'll correct myself ... Battlezone usually fused at F3 and skips F2. If F3 looks scorched I guess at some point someone has simply shifted the wires over to F2.

0VAC at the rectifier. OK - try a lead on the transformer side of fuse F2. Other lead on the orange wire that runs directly from the transformer to the rectifier. See if you get an AC reading now.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Yes 0V AC across the orange wires (but the fuse is still in the path).
I removed the connections from one of the other fuse clips and swapped

the rectified supply over to that clip and bingo 13.5V DC. So I know it's

the corroded clip.

Thanks folks for the advice. A much happier outcome than replacing T1.
 
Top