Battlezone - centering display

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Woohoo! Good news everyone...... On Saturday, an amazing friend (u72) came over on bearing a gift of a loan of a Battlezone PCB set.

So my BZ cab is now up and running while its original board is off being fixed.



However, the display is not vertically in the correct place and I am stuck on how to move it down. There are solder points on the PCB for X and Y centering BUT the manual doesn't list them as being present so it looks like that section of the board was generic.

Is there a control to adjust on the monitor, I would have thought so but I can't see one looking at it from the back.

We've taken Y-SIZE and X-SIZE in as much as possible to get an almost playable game but you can tell there's bits hidden in the cardboard bezel area.

Thanks
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
I have these notes from way back;

"Populate the (empty sections for centrering) boards with a 220K resistor and a 0.1uf capacitor, and a standard 10K trimpot, one for each X and Y".

I've never tried it but it's supposed to work perfectly. Alternatively I think you can adjust the monitor rings to centre the image, again never needed to do that either.

HTH

Dan
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
On my last BZ cabaret I adjusted the position of the picture using the monitor adjustment rings on the neck. It's nothing like as bad to do as on a colour monitor as there's only the 1 gun so no convergence to worry about.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
As its not my board i'd be more inclined to adjust the monitor. I'll take a pic of the monitor in question as i'm not sure what's in it, can you point me at the right ring?

I am showing my naivety here but I would have thought centering was down to the deflection yoke but i'm still on L plates on vector monitors.

(Did fix a 6100 on Saturday though that was spewing vectors everywhere randomly)
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
The neck has a pair of rings on it (just one pair in the case of a B/W vector). These rings are basically magnets and as you adjust them it has the effect of altering the overall deflection of the beam. The deflection board changes the deflection individually for both X & Y according to the voltage coming off the game board. This is considerably different.

In colour monitors you don't want to touch these rings unless you really have to as they align the Red, Green and Blue beams in relation to each other and if they're not spot on, you'll be there forever trying to get them back again and you won't get white until you do. For B/W it's pretty easy and you can use it to move the whole picture a bit.

You can also get a considerably greater movement by physically moving the yoke. But don't go there! The rings is like a fine tune.
 

forcefulfil

EDOT King
vacBacker
Feedback
17 (100%)
Credits
1,675CR
Monitor will be a G05-805
There are 4 pots on the defleftion pcb,ideally remove the monitor on the floor/chair to get ur hands in and adjust them,usually glued like the AR1/2

its on the opposite side to the H.V. cap so you shud be safe
smiley36.gif


ive never adjusted any rings on mine,somaybe the yolk rings have moved in transit,or messed previously

forcefulfil2013-08-12 12:56:46
 

kevwolf69

Newbie
Credits
52CR

kevwolf69

Newbie
Credits
52CR
Oh and one more thing to consider.....the probable reason the screen is off center is the most likely drift in component values so even if you adjust the yoke rings then you'll probably have to do it again when you get your original board back?....just my thoughts.
kevwolf692013-08-13 13:57:58
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Nice to see though that right under the section about populating the adjustment section of the PCB it goes on to explain the probable reason Atari didn't populate them themselves and that it's just as easy to do it via the adjustment rings. As we've suggested
smiley36.gif
 

kevwolf69

Newbie
Credits
52CR
Yup i see that but i'd still rather give myself the luxury of not having to mess around with 30 year old centering rings with flimsy tags. On my own Battlezone i had to slacken off the yoke and twist a tad for rotation. It wasn't that bad but i'm a perfectionist and wanted it dead straight. At the same time i looked at the tags for centering and decided then that i'd be reintroducing the centering circuit. I spent 16 years building/setting deflection units for Philips tv's and know the crappy parts our brothers in the east use to make their units. Swings and roundabouts i guess.
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
Yeah I've had G05 rings that really didn't want to move. I just didn't want to apply any more pressure in case I either broke them (or the tube). I managed to adjust it to "good enough".

Dan
 

kevwolf69

Newbie
Credits
52CR
guddler said:
OK, I give in. Go ahead and populate the missing electronics from the PCB (that's on loan)
smiley36.gif

I can't see where i mentioned he should do it to his loaner board, but yeah i'm sure for the princely sum of £2 for the components he could do both boards and forever be a hero to the guy that loaned him in the first place.....
smiley20.gif


kevwolf692013-08-13 18:26:24
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
smiley36.gif
Exactly! I think everyone that's been putting forward suggestions in here based on the PCB is overlooking the original question of "is there any adjustment on the monitor" and the fact the PCB is on loan!
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
I spoke with Andy (the loaner) and as it's basically 6 components he's happy for me to mod the board. Might need some advice on the components needed - i'll check what i've got in.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Been and looked at parts - I need all 3 which is surprising as I thought I at least had the resistors.

220k resistor - assume 0.25W will be fine

0.1uf capacitor - these aren't going to be electrolytic - what type? poly, tantalum?

10k trimpot - I had some of these but they aren't wide enough - arrrgh - I hate finding trimpots as there are so many different pitches
smiley6.gif


A little help please here.
 

kevwolf69

Newbie
Credits
52CR
I'm out of the house right now but I know I have enough spares to do your board. the trimmers I got are just the blue cermet type. my plan being if they are too big i'll just use cut off resister legs as extensions. pm me if you want me to slip them in the post. oh the caps are just ceramic radials. when researching the component types Google found most of the serial numbers for me and eBay did the rest......
 
Top