CRT Isolation Transformers

panpar227

Active member
Feedback
10 (100%)
Credits
114CR
Could somebody explain the reasoning to me behind some CRT monitors requiring an isolation transformer and some not?

I understand that running one that requires an isolation transformer WITHOUT one is not recommended but is there any danger in running one that DOES require one WITH an iso transformer?
 

obcd

Active member
Credits
3,830CR
It depends upon the monitor chassis power supply that makes the B+.

Modern monitor chassis use a switch mode power supply that is already isolated.

An extra isolation transformer doesn't harm as long as it's designed for the needed power load (or can handle a higher load) and outputs the correct voltage for the monitor chassis.
 

tin

Active member
vacBacker
Feedback
3 (100%)
Credits
673CR
I understand running one that should have an isolation transformer without one in place will work, but the whole chassis will be live, and if you touch it (and aren't properly insulated) you are toast (or flying across the workshop or something). Oh and it might blow up the board(s) it's attached to.

I read up on it but still don't really understand why :) something to do with neutral coming out of the mains actually being the same as earth yet after an isolation transformer it's not any more.
smiley5.gif


and yeah running a chassis that doesn't need one with one in place anyway makes no difference AFAIK.
tin2015-09-16 19:03:49
 

obcd

Active member
Credits
3,830CR
Just look at the symbol of a transformer It's basically 2 isolated windings. The one connected to the mains converts it's voltage into a magnetic field. The other winding converts that magnetic field into a voltage again that is used to power the monitor chassis. There is no electrical connection between those windings. That's why it's an isolation transformer.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
tin said:
I understand running one that should have an isolation transformer without one in place will work, but the whole chassis will be live, and if you touch it (and aren't properly insulated) you are toast (or flying across the workshop or something). Oh and it might blow up the board(s) it's attached to.

I read up on it but still don't really understand why :) something to do with neutral coming out of the mains actually being the same as earth yet after an isolation transformer it's not any more.
smiley5.gif


and yeah running a chassis that doesn't need one with one in place anyway makes no difference AFAIK.

Sadly not, you'll see things blow up, gunblade or ordyne can explain better why and I know its been given in a post elsewhere but I couldn't find it.

In my head its the same reason you don't stick your scope direct on mains electricity.

Wish I could remember it but just don't. If it needs an isolation transformer, give it one, if it doesn't, putting it on an isolation transformer, as obcd says, of the right rating and voltage compatible with the chassis will be fine.
 

obcd

Active member
Credits
3,830CR
The electric distribution company grounds the neutral wire at the transformer houses. Due to that, you can have a current flow between life and ground (earth). If you touch a point connected to life, your body becomes a conductor as well and you have a current flow towards earth. Normally, you have a differential switch in your meter closet that cuts the power if the current passing trough life is not equal to the current passing trough neutral. (Since it flows to ground trough your body, it doesn't pass neutral) That's the reason why your chassis needs to be isolated from mains. Basically, if you wouldn't be able to touch a thing, you could work without isolation. Old Black and White televisions where like that. I have also seen it on electronics of washing machines.

So basically, you will measure approx. 240V between life and ground, and only a small voltage between neutral and ground. On older net's it's possible that you measure approx. 110V between both wires and ground. I wan't try to explain why it's like that unless you really want to know. The important part is the fact that you can create a current flow between life and ground (and sometimes neutral and ground as well)
 

RSwanson

User
Feedback
1 (100%)
Credits
205CR
It is a confusing subject, so I will try my best to describe my "understanding" (please correct me if I'm wrong).

Firstly, you have to remember that in theory a current will only conduct to its reference point (ie ground).

During power distribution (external to our homes), the neutral was commonly tapped to GND.

In traditional TV sets, the chassis was "live". The reason for this is that it's encased in plastic, so doesn't require the use of safety GND in use today.
And by "live", although that sounds scary, it doesn't mean the chassis was connected straight to the live AC, but that it was used as a common GND, and hence is in the conduction path.

When those TV sets were altered and used in arcade cabs, the chassis was exposed, which meant from that point on it was necceassry that they were connected to the home (safe) earth GND).
If there were no ISO, it would mean that at the point of DC rectification, the "hot" would see a short to the safety GND (Neutral-GND tap) and conduct, meaning the rectifier diodes and associated circuitry would see a short circuit and burn.

However, with an ISO, the Neutral/Live have no association with the above GND, which means that in theory you can touch one of the ISO secondaries and GND and not be electrocuted (please never try this, it's just theory). The most common cause of eletrocution is hot->GND. hence why ISOs were recommended. You can still die from touching both secondary outputs though.

Does this make sense? I'm more than happy for people to correct this.
 
Top