Data IO 29b - Troubleshooting

Pilljar

Newbie
Credits
4CR
DATA I/O Serial connections

25
pin 9 pin


6 1

2 2

3 3

20 4

7 5

6 6

5 7

4 8

9 not used


















Instructions for using Data I/O 29B
It will only run via updated promlink in XP
or earlier. To run in VM follow these instructions.

1 boot main computer. Fresh boot is essential!

2 Open VM player and XP.

3 Plug USB-Serial adapter in configured as
COM1.(disable normal COM1 first.)

4 Turn Data I/O on. Ensure settings are
9600,8,off,stop 1,.

5 Press Select, F, 1, Start, Start.

6 Open updated version of promlink.
Settings should be as in 4 above.

This should give good two way activity.

DO NOT USE FB (open port. This kills all
transmission from computer to Data I/O).

Ensure no chips are in sockets when turning
Data I/O on. It seems to destroy the chip select.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
I'm still no closer to resolving this.

I have had the unit stripped down to the bare motherboard and tested for faulty ICs and found nothing wrong.

This is incredibly frustrating, I really need someone with a working 29B to verify if the problem is my unit or my PC setup.

Anyone prepared to give it a whirl for me on their PC setup?

Equites2014-05-19 12:22:14
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Equites said:
I've no way to contact him outside of UKVAC.

Ok, I thought I'd sent you his details but clearly not. Sorry about that. Sent now :)

I've previously spoken to him about this and he said he has no problems with you contacting him directly
Purity2014-05-19 13:55:04
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
I've tried to contact Tim but had no success unfortunately.

I have now tried to contact Mark of Retroclinic in an attempt to bring this to a satisfying conclusion.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Since there is an overwhelming interest in this thread, I thought I would update it.

To date I have not been able to get the 29B to talk to PROMLINK.

I have been successful in contacting Mark (retroclinic), who kindly sent me his proven working Parallel/Serial cable. This eliminates the cable.

Which leaves just the laptop/PC I would think.

I have now purchased an old Toshiba Tecra 500CDT laptop. Old bulky thing, with parallel and serial ports at the rear. I have now installed MSDOS 6.22 onto the hard drive, and intend to run PROMLINK in native DOS.

Wish me luck.Equites2014-08-20 17:24:12
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Ok, native DOS has not worked either.

The only thing I can add, is that I also tried PROMLINK 3.1 and 3.4. I managed to get as far as the correct sockets being highlighted via LED by PROMLINK. So it would seem some comms is there, but PROMLINK still complains about no connection to programmer.

PROMLINK 6.1 behaves exactly the same.

I am officially throwing in the towel, I really have had enough. I've wasted enough time on this stupid thing. I feel like I need to smash it up to get some kind of closure.

If someone wants to help me out and test it on their setup, that would be useful, otherwise over and out.
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
If I had a bit more time I'd get my unit out and get it up and running. I got it from Guddler and I think it's supposed to work. When I do I'll ping you Nad.

Dan
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
DanP said:
If I had a bit more time I'd get my unit out and get it up and running.   I got it from Guddler and I think it's supposed to work.   When I do I'll ping you Nad.

Dan

Thanks Dan, I need a break from it anyway :)
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
Found this info on the net

Promlink Software for Data I/0 Eprom/Prom programmers
Models supported

•29B UniPak
•29B LogicPak
•UniSite, Unisite SetSite
•2900 Programming System
•3900 Programming System
•Series 1000, 1000LC
•212
•288

Promlink 6.10 - complete package - Here is the software for used with many older Data I/O programmers. It works under DOS or any flavor of Windows, including Windows 2000. The first zip is the entire distribution that was last available on the Data I/O ftp site and is no longer available from them. Just unzip and your ready to go.

Update: 10/27/2004 - New Patched Binary for Windows XP

Patched Promlink 6.10 - fixed binary - The second file, pl.exe, replaces pl.exe in the Promlink directory. It fixes a divide by zero problem that Promlink has when trying to run it under Windows 9x, 2000 and Windows XP on fast (1 GHz or faster) CPUs. Patched by Mike Coates.

Device lists for the above programmers can still be found on the Data I/O ftp site at:

DataIO FTP Site
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,016CR
just a ps to this thread - this popped up on the tech tools forum may be of interest.

---

Actually there is a great support group on Yahoo for the Data I/O
programmers - I joined it years ago and it is moderated by Alferd Marin
who bought up all of I/Os obsolete gear. Alfred is a great help, often
giving advice on setups etc. for the various older I/O gear.

Go to Yahoo.com and look for the DATA_IO_EPROM group - easy to join!
Tons of archived info on upgrading the 29 series machines including
adding more memory and getting them to the last revision level. Well
worth the visit!
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Macro said:
just a ps to this thread - this popped up on the tech tools forum may be of interest.

---

Actually there is a great support group on Yahoo for the Data I/O
programmers - I joined it years ago and it is moderated by Alferd Marin
who bought up all of I/Os obsolete gear. Alfred is a great help, often
giving advice on setups etc. for the various older I/O gear.

Go to Yahoo.com and look for the DATA_IO_EPROM group - easy to join!
Tons of archived info on upgrading the 29 series machines including
adding more memory and getting them to the last revision level. Well
worth the visit!

Thanks Mike, I absolutely give up with this thing. My only other option right now is to try and get my hands on another 29B unit.

I now believe the problem is with the programmer, where exactly is a mystery. It is either the main unit or the 29B UniPak. I need to eliminate which one with another working unit.

Quite frustrating, I needed to check 2532 ROMs today on a Pacman and don't have the facility.
 
Top