Gorf voltages

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
Finally got my step down transformer for my Gorf upright.

After checking the voltages coming out of the linear power supply, they look fine apart from the +12 (pin 17) which is running at 13.45v, to high?

One other question, should I be getting a voltage out of pin 1 ?

Hopefully this should be ok for me to connect the boards up and cross my fingers and toes.

Darren
 

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
Right I've turned the volts down and took the plunge. Sadly and rather predictably it doesn't start up.

Top and bottom marquee light are not working, also the joystick lights.
There is a faint line on the very top of the screen, video can be seen here.

IMG_20160903_57775.jpg


Also no sound, but noise when adjusting the volume.

Monitor is a Wells Gardner 19K 4606.

I guess I'll have to pull the boards out, check them over and clean them up. Any advice greatly appreciated.Shinydaz2016-09-03 16:24:03
 

Hurray Banana

Moderator
Staff member
vacBacker
Feedback
8 (100%)
Credits
2,756CR
Look for corrosion on the connectors (al of them).

I had to re pin all the connectors as mine were green. This is one of my gorf ones. If you have't got one get a decent ratcheting crimp tool.

corroded.jpg


You'll also need to check over the caps on that linear power supply
 

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
Tempted to get a new power supply, but leave the old one in place.
Looks like a needle in haystack job, going to keep me busy getting this running I think, cheers for the info.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Also although not listed, i have all the KK156 connectors and pins to redo the harness.

Message me if you need those and i'll add them.

The shop is in its early days and i've about 2000 products to eventually add but i want to do them right.
 

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
Yes I saw that switcher kit the other day. I'll get some stuff ordered off James over the weekend. At least it will have a safe supply that's not going to fry the boards if it fails. The internals of the cab look pretty mint, no hack jobs. I did notice its missing one of the bulbs for the rank lights, easy find?
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
I replaced all my rank light bulbs and control grip bulbs with warm white LEDs

It's surprising what I have that I've bought massive amounts of.

The rank lights are a 161 wedge and the control grip lights are a 44 if memory serves.

I'll add them all.

I probably have the tungsten ones as well somewhere.

(Sounding like a right sales whore. I just bought bulk cos it was easier for maintaining all my stuff)
 

LAZORIAN

Active member
vacBacker
Feedback
2 (100%)
Credits
260CR
Good luck with this shinydaz Gorf is a great game and an awesome looking cabinet. I am just about to do the switcher conversion myself so I'll share anything relevant.

@RGP looking forward to seeing the shop stock increase James.
So when are the working board sets going to become available? :D
 

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
Yes any helpful info would be greatly appreciated, yours running at 110 or 240 Ianski? I hear the voltage conversion (110 to 240)isn't to hard?Shinydaz2016-09-03 17:24:15
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
GORF in MAME isn't bad for sampling the game but you can't beat the cab for the experience.

You should be lucky - on the primary transformer you should find input taps for 230vAC at very least.

I have in about 4 that I've handled now.

Do yourself and the transformer a favour - move the GI power to 230v as well - the US machines all have 110v bulbs in - when these go you'll have to put 240v in which will run at half power - half brightness.

I put 240v CFL's in my home one and boy does it run cooler and brighter.

It's one of those obvious design flaws where Midway didn't see the game being around long.

I'm going to do a video about all these bits of things I think.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Move all blue wires from 127v to 240v

Change E27 110v bulbs to 240v

OR

Figure out which of the blue wires is the power to the other transformer etc and move that to 240v leaving the rest on 127v and leave your bulbs alone

OR

Use a Maplin step down which may go over the VA rating because of the extra lamps etc

OR

Embed a high VA transformer.

Personally as the MT-87 is suitable already I'd move the blue wires and replace the bulbs
 

Shinydaz

Active member
vacBacker
Feedback
6 (100%)
Credits
814CR
So swap the 3 blues to the 240 tap and the green wire coming off the middle fuse? does that want to stop on the 115 tap? Or move it with the 3 blues to the 240?

IMG_20160903_31287.jpg


Also when I come to connect the new 240v power cable, which terminal is Live and Neutral, both my inputs are black. Just checked with meter, live is on the right, on the picture, just to confirm.
IMG_20160903_27617.jpg
Shinydaz2016-09-04 13:28:59
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
The MT87 makes many voltages - one of them is 110v

The 110v then goes through a fuse into the second isolation transformer which is a 1:1 which goes to the monitor.

You only need to move the blue wires as all you're doing is selecting the input voltage on the primary side of the Mt87.

This is the equivalent of putting a Maplin transformer outside the cab.

Just remember to remove the GI bulbs if they're still all 110v as they'll over-volt and blow.

Disconnect everything in the cab like the power supply and monitor and take a reading at those points after moving the blue wires to make sure you get expected voltages before you plug sensitive devices in.
 
Top