Help please....

G

Guests

Guest
Well my cab lasted... about a day...

Got the screen going, decided to have a go on it tonight. Got really into it having fun then suddenly this happens...

2016_04_07_22_24_49.jpg


2016_04_07_22_24_20.jpg


Really annoyed... I'm assuming this is pretty serious as it happens when you power off the machine and then back on again.

What would this be dare i ask? I'm assuming RAM..?

smiley19.gif
 
G

Guests

Guest
I pulled the board out to have a look over everything see if i can see anything obvious and like you advised, see if any of the chips are loose etc...

Here's the board:

2016_04_07_22_52_11.jpg


2016_04_07_22_52_57.jpg


2016_04_07_22_52_18.jpg


2016_04_07_22_52_23.jpg


They looked fine but i lightly pressed on them anyway to make sure.

Put it all back together and oddly enough....

2016_04_07_23_06_02.jpg


2016_04_07_23_06_01.jpg


All textures are normal again... The lines you see on screen are actually normal they have been there since i put the new chassis in today. They are white dots equally spaced apart they come close to remaining static but then move again pretty quickly... I asked Gunblade about this via PM and he said its an earthing issue however I can't really figure out where... Could this of caused that texture issue?

Seems to be working again now... Scared to use it now though...
smiley5.gif


rotunda2016-04-07 23:15:21
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
Given the monitor interference you're getting as well (which is typical of a ground/earthing issue) I would give your connections a close inspection and testing - the connector where the board plugs into the cab. I'd also check the signal connector on the monitor re the interference.
 
G

Guests

Guest
stegrey; this is the longest i've ever had it on, plus the heating was on too so yeah.

big10p; I've had a good look over the connectors when i took it all out, they all seemed ok. Where is the signal connector? Sorry I'm new to most of this.
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
I don't know what monitor you have but there should be 2 connectors that plug into the chassis. One is for power, the other is the signal connector (red, green, blue, sync and ground). Use a multimeter to test the ground wire (should be black) actually has continuity with ground.

Also, the PCB connector may look OK but I'd also check continuity of all pins, between connector and PCB, when it's plugged in but not powered up. While you're there, probably a good idea to check input voltages too (with the cab turned on, obviously).

I'm no expert either, to be honest, but it's best to check the basics before anything else. stegrey has a good point about there possibly being a heat issue too.

big10p2016-04-08 00:08:01
 
G

Guests

Guest
Ok, I've checked the continuity between the RGB black wire and the ground and there is continuity there.

I will check the PCB pins shortly, the voltages are all ok I tested them awhile back, 12.04 and 5.16 or so.

I've been going over everything, spotted this..

2016_04_07_23_50_44.jpg


Thought it might be a damaged wire but it seems to go into this...

2016_04_07_23_51_54.jpg


Which turns out to be the rear fan... I've actually completely forgotten to check this fan, ever....
smiley32.gif


Tried it and it is indeed dead... so I need to try and fix this, I've tried putting the wire in but it doesn't work still.

I'm guessing it got a little too hot. Although that is just an exhaust fan so i fail to see this being the reason behind it... but then i could be wrong I have no idea how hot these boards run.
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
Yikes! Don't go near that exposed wire with the power on. No idea what the blue clips are for, TBH. Maybe someone else knows? Bit confused as the wire colouring suggests they carry a mains supply which I can't see how it would be used just to power a fan.

Anyway, with the fan not working I guess it may well be the cause of an over heating issue. The manufacturer wouldn't have fitted the fan if it wasn't needed.
smiley1.gif
 
G

Guests

Guest
That is true, plus it was up against a radiator at the time now i think about it with the heating on... Thankfully i've booted it up 3 times now and its working fine so I expect it was just too hot no damage done?

And yeah the fan is a 240v fan so yes... very careful around that wire! What type of connectors are those? I need to order one as that one that it had is the wrong size anyway it doesn't hold the wire in correctly.

Or would there be a better way to wire the fan back up?
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
So those blue clips actually connect the fan wires to the power wires? It's difficult to see from the pics as I thought it looked like they just clipped across the wires, serving no purpose that I could see! I guess they're used to tap into the power wires that connect to something else?

Anyway, they look pretty nasty to me. I'd just get a terminal block like in this pic (snip a block of 3 off the end and connect it up). Should be able to get one from a local DIY shop etc. - costs pennies. Just make sure you get one rated for the voltage/amperage of the fan.

mijewAg0GIk9yOFoFRLeEgQ.jpg
 
G

Guests

Guest
ironically I've done just that just a moment ago so it's much better now.

The blue wires run up to the screen and flo tube so i presume its the 240v feed for the crt and flo tube. Someone has spliced the 240v exhaust fan to this power source, no idea why.

Anyway even with this done that fan still wouldn't work so i took it off to chck it on another power source and...

2016_04_08_01_09_43.jpg


It fell to pieces when i took it off
smiley36.gif
New fan it is..
smiley32.gif


rotunda2016-04-08 01:19:01
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
Ah!
smiley1.gif
Not sure, but this issue may be the cause of your monitor interference, too. If you still get interference after this, try disconnecting the fluorescent light and see if that helps. Sometimes a dodgy ballast can cause screen interference.big10p2016-04-08 01:28:10
 
G

Guests

Guest
I just tried it without the flo tube connected at all there is one lead which runs up to the flo tube and powers it i disconnected the block connector and turned the machine on, still had the same white dots unfortunately even though the flo tube was off.

On a brighter note, I've ordered a nice new fan for it, they still sell the fan that came off it!
smiley3.gif

rotunda2016-04-08 01:41:56
 

JohnUK

User
Credits
33CR
I don't think those blue clips are designed for 240v and I've only ever used them for 12v on car audio when splicing remotes for amps etc... Not sure but would most likely melt under high load.JohnUK2016-04-08 10:41:58
 
G

Guests

Guest
Good job I've swapped them out then i guess :)

I snipped the resistor on RGB and the white dots are far more visible.

2016_04_08_12_15_54.jpg


snipped ^^

2016_04_08_12_22_04.jpg


Soldered back to normal ^^

The dots become more transparent with the resistor in place, I'm guessing i need a new resistor?

2016_04_08_12_26_50.jpg


Any idea what rating this one is?
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
75 ohms.
smiley1.gif


Slightly difficult to tell but is there a grey stripe next to the violet stripe? If there is then it's 875 ohms.tb20002016-04-08 12:43:46
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,086CR
I haven't seen a resistor there before. Why's it needed?

BTW, I'd move your cab to somewhere away from the radiator if you can, or keep the rad turned off.
 
G

Guests

Guest
Yeah there is a grey stripe

2016_04_08_12_51_55.jpg


big10p learn't that the hard way fella I think heat is what caused that texture glitch to occur. I've had it on for a short while today though and its running fine thankfully.
rotunda2016-04-08 12:57:16
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
big10p said:
I haven't seen a resistor there before. Why's it needed?

BTW, I'd move your cab to somewhere away from the radiator if you can, or keep the rad turned off.
I have, seen it before quite a few times, you tend to see it on some Namco stuff that's a certain res and also some Sega stuff, for example the system 22 Namco loom I have has got one in and also I had a Sega STV board that needed it otherwise it jittered at high speed on certain games like Decathlete. It think it's mainly to do with what pixel resolution it runs at, or if it's interlaced.
 
Top