Let's fix Asteroids Deluxe

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Ronnie Dent said:
If I disable the watchdog while in test I get a constant beep, but in play mode it's silent screen is blank but when I credit it the buttons flash and I can start a game with sound and some graphics I can see my ship and bullets but slightly distorted and random lines are drawn whilst the spot killer goes on and off? did not want to do this for too long but surely this should help narrow down the fault somewhat I hope lol

Thanks Ronnie

Not really, troubleshooting the VSM section on these vector PCBs can be a nightmare, even for the experienced.
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
The prom at C8 has been previously removed and or replaced? it has a socket but the ic looks like it's been pulled? I see this in the romset folder but how would you go about writing one of these? and is there only one prom?

Thanks Ronnie
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Ronnie Dent said:
The prom at C8 has been previously removed and or replaced? it has a socket but the ic looks like it's been pulled? I see this in the romset folder but how would you go about writing one of these? and is there only one prom?

Thanks Ronnie

If it's been pulled/socketed, then its likely just been read to verify it is still 100%

Game will not run without C8.Equites2014-05-23 11:02:29
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
Equites said:
Ronnie Dent said:
The prom at C8 has been previously removed and or replaced? it has a socket but the ic looks like it's been pulled? I see this in the romset folder but how would you go about writing one of these? and is there only one prom?

Thanks Ronnie

If it's been pulled/socketed, then its likely just been read to verify it is still 100%

Game will not run without C8.

Thanks Equites for your replies, I don't have a device to read C8 so will need to assume for now it's good! I'm thinking if I disable the watchdog and probe the timers etc I might hit lucky and find some stuck IC outputs, or not sure if best with ram removed and board halted? and also read of lifting a pin to disable dmago while testing?

Thanks Ronnie
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Ronnie Dent said:
If I disable the watchdog while in test I get a constant beep, but in play mode it's silent screen is blank but when I credit it the buttons flash and I can start a game with sound and some graphics I can see my ship and bullets but slightly distorted and random lines are drawn whilst the spot killer goes on and off? did not want to do this for too long but surely this should help narrow down the fault somewhat I hope lol

What you've done DOES narrow it down a bit to me. But I need to look up some more information. I think it tells me it's not the state machine and there's further diagnostics you can do to narrow it down further.

Would just like to add that if it IS the state machine then there isn't a way in hell that you can diagnose it with a logic probe alone. The state machine is a very simple custom computer made up of a few logic chips but it's very, very tightly looped onto itself (if that's the right way to put it), where every state feeds onto the next and the slightest fault in there will have it locking up faster than you know it which pretty much rules out any traditional method of looking for faults...

OK, the following is for an Asteroids PCB but they are so similar, you should be able to find the chip in question on an Asteroids Deluxe PCB and do the same. Socket the LS42 chip at L5 and lift pin 1. Or otherwise lift pin 1. This pin is the DMAGO signal. If the game now runs blind then the fault is in the vector side of things, if it still doesn't run then your in luck as the fault is in the program side of things. Personally I just snip the leg of the chip with some good quality sharp side cutters making sure I do it in such a way that it can be re-soldered. But socketing is better if you can.

That's a crucial first step.

I'll look up the other diagnostics in a mo...

guddler2014-05-24 11:40:58
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, pin K on the edge connector is marked as 'Diag Step'. This allows us some further diagnostics than just the test mode. I can't remember exactly how you initialise this extra mode. You either ground that pin, then go into test mode to start, or you momentarily ground the pin when you already are in test mode. Either way, do it. There are a number of steps and depending on which it gets as far as (if any) will tell us a bit more about where in the vector side of things it's getting tripped up. This assumes it's not the state machine itself.

There are a total of 4 'diag steps'. Each will draw a line. Tell me how far you get into the 4, if at all. It's still not simple from there but it may help narrow it down.
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
Hi Guddler thanks for this info it is much appreciated

I will try and isolate that pin if possible by de soldering it and see where I get.

with watch dog disabled I was able to start a game with some graphics and random lines drawn.

And removed a ram which beeped low in test and halted.

But I think what you suggest is where I need to go. will report back

Thanks Ronnie
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
Right I lifted pin1 of L5 well snipped it! and game plays blind, but any combination of grounding K on edge just produces a slight beep? also in test same beep by pushing any button, spot killer stays on?

thanks Ronnie
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
That's not good news. Snipping that pin basically bypasses the "draw picture" processing by the DVG. You've proved that the regular 6502 program is running, so the ram and rom are probably good. That means the problem is in the DVG (the CPU in TTL mentioned by Guddler). Finding faults in there is next to impossible without a lot of grunt work or serious tooling.

Dan
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
DanP said:
That's not good news. Snipping that pin basically bypasses the "draw picture" processing by the DVG. You've proved that the regular 6502 program is running, so the ram and rom are probably good. That means the problem is in the DVG (the CPU in TTL mentioned by Guddler). Finding faults in there is next to impossible without a lot of grunt work or serious tooling.

Dan

Thanks Dan, just my luck
smiley18.gif
what about this Diag step test thing? does the fact I only get a beep in test when grounded tell anything

Thanks Ronnie
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Yeah, it tells you that it can't run the Diagnostic Tests
smiley36.gif


Either that or I'm not telling you how to do it right. So, just to recap. With pin 1 of L5 connected, the watchdog enabled and everything as per normal do you get ANYTHING up on the screen or any kind of play out of it before it crashes or is it just a blank screen in a very tightly resetting loop?

If it's the latter then I'd be pretty confident it's a state machine (DVG) issue and I can't remotely diagnose an issue there.
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
guddler said:
Yeah, it tells you that it can't run the Diagnostic Tests
smiley36.gif


Either that or I'm not telling you how to do it right. So, just to recap. With pin 1 of L5 connected, the watchdog enabled and everything as per normal do you get ANYTHING up on the screen or any kind of play out of it before it crashes or is it just a blank screen in a very tightly resetting loop?

If it's the latter then I'd be pretty confident it's a state machine (DVG) issue and I can't remotely diagnose an issue there.

With everything connected it's in a very tight reset loop nothing on screen! I'm doomed lol, I do have a scope but no knowledge how to use it! I guess I will need to send it away or buy a worker
smiley18.gif


Thanks for your help guys if you can think of anything else I could try fire away

Cheers Ronnie
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Sorry dude, but it does sound like a DVG state machine error and I've not got around to writing any routines to fix that. In theory if it was something like the sub routine stack (which from memory is the LS170 / LS670 chips and associated logic) then you'd be able to get somewhere with the diag steps. That's the point of that test is it does different things, each more complex and involving more hardware in turn. The first is a very simple draw command that draws a line from the bottom left corner to the top right corner and if it's not managing that...
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
guddler said:
Sorry dude, but it does sound like a DVG state machine error and I've not got around to writing any routines to fix that. In theory if it was something like the sub routine stack (which from memory is the LS170 / LS670 chips and associated logic) then you'd be able to get somewhere with the diag steps. That's the point of that test is it does different things, each more complex and involving more hardware in turn. The first is a very simple draw command that draws a line from the bottom left corner to the top right corner and if it's not managing that...

Thanks Guddler, any idea on cost of repair against cost of replacement? I guess £80 might buy a good board, but be a shame as this is a nice clean board

thanks Ronnie
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
I would say on average £80 for repair sounds about right. Expect to pay more than £80 for a working PCB though, more like £120-£130.
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
not sure if any relevance? but I put back pin 1 of L5 and grounded watch dog as before and credited it up to start a game but this time it was blind? so might have a screen issue now or something has changed? so maybe diag step was working? is it worth connecting xy to my scope to see if it displays?

thanks Ronnie
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
It's no good grounding the watching dog and trying to coin up and playing a game. Ground the watchdog is simply a step to take when using diagnostic equipment such as the Atari CAT box or a Fluke 9010/9100. With that grounded you won't get the game reset that it needs to kick the board into life - you can of course manually do that with the reset button. Unclear if you're doing that or not.
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
guddler said:
It's no good grounding the watching dog and trying to coin up and playing a game. Ground the watchdog is simply a step to take when using diagnostic equipment such as the Atari CAT box or a Fluke 9010/9100. With that grounded you won't get the game reset that it needs to kick the board into life - you can of course manually do that with the reset button. Unclear if you're doing that or not.

Okay it was just I tried that yesterday and it played and displayed some graphics and random lines? I thought with it not doing that now maybe the screen is flaky? and I was not seeing the diag step

Thanks Ronnie
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
I find the early vector boards and how they implemented maths for vectors and other sub processes fascinating.

If the board can be saved then it should.

I've looked over the schemes for Ast and AD and quite a lot of it is genius for the time. I wouldn't know where to start outside the program side.
 
Top