MONITOR EMERGENCY!

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Calling all monitor gurus!

I am swapping over a brn free tube with a slightly burnt one on my Dig Dug Euro.

Problem is, now I have them all in bits ready to swap - the old tube has 1 les pin on the neck socket!

The chassis is a good 'ol G07 with a Hitachi tube 51OUJB22 with 9 pins + 1 pin

The new tube is a Rauland 19VNJP22 which only has 8 pins + 1 pin

I was sold this as a straight swap, and I think it is, as the G07 neck board doesn't have the offending extra pin wired up?

I really need some advice before doing this!!

Another quick tutorial on checking the yoke wires too would be helpful (I forgot
smiley9.gif
)
 

jengineer

Senior Member
vacBacker
Feedback
49 (100%)
Credits
1,205CR
post some pictures up dude,

maybe someone can tell you if a G07 tube is the same as a G19 tube? and if the neck is the same?
jengineer2014-06-30 13:26:16
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
The neck board would actually fit ok and all the other plugs will fit - I just want to be certain.

Original tube - 9 pins + 1 pin (note the ceramic resistor on the degauss wire

20140630_135243.jpg


New tube - 8 pins + 1 pin (doesn't look like it, but there are 8 pins + 1 pin on this)

20140630_1351290.jpg
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Both tubes have 6.3v heater voltage and use the CR23 B&K Rejuvenator plug so that's a good start. I'll just see if I can spot any slightly more concrete answer.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Sadly, having just looked at schematics for both monitors, even with them using the same CRT adapter, I'd not like to commit either way. The schematics for the earlier G07 chassis are not at all clear about pin numbers on the neck PCB whereas the G19 are. Unfortunately the way the schematics show the beck board is entirely different so it's difficult to make a decent comparison.

You need someone with first hand knowledge of those CRTs.
 

jengineer

Senior Member
vacBacker
Feedback
49 (100%)
Credits
1,205CR
virtvic said:
Oh poo. I was sold it as a G07 swap - but let's wait and see if Gunblade or Ordyne chime in with their knowledge.

Cheers guys!

vic, we didn't mention about chassis models, it was just sold as an Electrohome tube
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Jengineer - do you still have the chassis for it? I found our old pm conversation about it and you mentioned you had the chassis too?

I know it's a long shot...
 

jengineer

Senior Member
vacBacker
Feedback
49 (100%)
Credits
1,205CR
I don't have any Electrohome chassis anymore but I remember giving it to snap, it worked but the tube was knackered and needed a rejuv

it was this one below




jengineer2014-06-30 20:02:50
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Cheers, James!

I got this first -

2014-08-15_20.08.09.jpg


A quick twist to the yoke and...

2014-08-15_20.26.06.jpg


Colours on the left hand side are pretty out of whack, so Ill have to have a go at the rings a little bit to try and improve it. Still happy I've done a tube swap. I've only ever done an asteroids one before.
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
It's not quite glorious...yet!

Is there anyway to get a static grid on the screen, so I can adjust the convergence properly?

I tried dip2 switch 5 (freeze) on the boot up rug, but it freezes just after the grid disappears...
 
Top