Another massive job on my list of stuff to do ticked off
, looking at old photo's i must of had these original arcade carpet tiles for 10 years, quite a few bought them but not seen anyone else really show any photos of them down
It's bad enough 3 months ago I couldn't even get in the door of my building without moving stuff but getting somewhere at least, most were all stored in here so I had to tidy stuff up so I could get them out which were taking up much space, this job would of been easy with nothing in here but when its full of machines, monitors, boards, control panels etc I've had to move so much it's not funny, and if that ain't bad enough I've had to clean all of them before putting down, wait for them to dry with hardly any sun, now we get some when I've done it, on top of that get the Chewing Scum off loads of them, as well as sort out fag burns and glue, wood, concrete, paper, foam and other stuff off the back of some stuck to the glue
Then had to put my tent up again so I could pull out 4 cabs and loads of stuff in case it rains so I can move the others about, it's like those puzzles with 1 square missing. move tons off the machines before moving them and then try to do a quarter at a time, normally you work from middle so the edge ones are cut down equal but when you can't see most of the floor that don't work, also being 3ft square it's hard to see where they will end up so decided to clear corner where both doors are, lay some out to see where they will end up, started with side single door and worked over to double doors, worked out well, in middle of door way it i was hoping to start a complete one and without having to cut them along the left wall, the double door 1st side had to be trimmed a little into door way, which left the right side again full and right up to skirting board, just had to make sure I got the first few perfect else it starts going off at slight angle, so had to move 2nd one again, glued the first 3 down and the rest I didn't bother as they are quite heavy and once down they don't move
They cleaned up well considering the state of them but it's took me about a month total with all the clearing stuff and cleaning but really happy with it, plus I moved a few things about and can now get to some machines to work on them in years
It's bad enough 3 months ago I couldn't even get in the door of my building without moving stuff but getting somewhere at least, most were all stored in here so I had to tidy stuff up so I could get them out which were taking up much space, this job would of been easy with nothing in here but when its full of machines, monitors, boards, control panels etc I've had to move so much it's not funny, and if that ain't bad enough I've had to clean all of them before putting down, wait for them to dry with hardly any sun, now we get some when I've done it, on top of that get the Chewing Scum off loads of them, as well as sort out fag burns and glue, wood, concrete, paper, foam and other stuff off the back of some stuck to the glue
Then had to put my tent up again so I could pull out 4 cabs and loads of stuff in case it rains so I can move the others about, it's like those puzzles with 1 square missing. move tons off the machines before moving them and then try to do a quarter at a time, normally you work from middle so the edge ones are cut down equal but when you can't see most of the floor that don't work, also being 3ft square it's hard to see where they will end up so decided to clear corner where both doors are, lay some out to see where they will end up, started with side single door and worked over to double doors, worked out well, in middle of door way it i was hoping to start a complete one and without having to cut them along the left wall, the double door 1st side had to be trimmed a little into door way, which left the right side again full and right up to skirting board, just had to make sure I got the first few perfect else it starts going off at slight angle, so had to move 2nd one again, glued the first 3 down and the rest I didn't bother as they are quite heavy and once down they don't move
They cleaned up well considering the state of them but it's took me about a month total with all the clearing stuff and cleaning but really happy with it, plus I moved a few things about and can now get to some machines to work on them in years