Pleaids IC

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Hi everyone,

I'm trouble shooting a Centuri Pleaids PCB and have found a pair of faulty ICs. They are located at IC26 & IC33 on the CPU board. The ICs are labelled M3-7611-5 and the manual is showing these as bipolar prom 7611-5 (Harris). In another working board I have TBP24S10 chips at IC26 & IC23.

I know very little about what these particular chips perform. Are the chips a direct swap or are these things programmed. I know I saw something about bipolar chips on a Galaga repair but are these similar?

Any help greatly appreciated.
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
They are 1Kbit (256x4-bit) bipolar PROM chips (tri-state). They need to be programmed with the correct data for Pleiads. You can swap in the TBP24S10's from the other Pleiads board to make sure they are faulty.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
shep said:
They are 1Kbit (256x4-bit) bipolar PROM chips (tri-state). They need to be programmed with the correct data for Pleiads. You can swap in the TBP24S10's from the other Pleiads board to make sure they are faulty.

Hi, yes I bought two non-working Centuri boards from the States. I've just repaired one and the second is throwing up this issue. Swapped the ICs around and problem disappears. The second board also has a reset issue which I haven't investigated yet - it plays demo perfectly and coins but press start and it resets.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Equites said:
Yeah PROMs, they usually run quite hot too.

Yes these are running hot. The resulting graphics problems vary but the main one is colours. Is anyone able to copy and program the data from the working board I have? The chips are available from littlediode on Ebay.
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
I think I have some equivalents (82s129). Let me check. If you can wait a week or so I should be able to help you out. I'm unlikely to get the chance to program these until the weekend. No need to send me the chips, I should be able to get the data from MAME.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Sounds like you're already sorted but if not, I can program the equivalents (82S129) but not the Harris parts. No idea if I have any 82S129's though.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
I can burn the Signetics 82s129's but not the equivalents, at least not until I can get my damn Data IO 29B working with Promlink.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
shep said:
I checked. I have equivalents (2 different types).

That's fantastic. Just let me know how much I owe you for doing this. I really appreciate the assistance from everyone.

However, that won't be the end of the story. I still have that resetting issue which I have yet to investigate. Please stay around to help me out a little more.
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
I'm not fussed about payment for this since you just bought a board from me, however, a small donation to UKVAC would be cool
smiley1.gif
.

The resetting problem could be many things but one possibility is a ROM problem. Try reseating the EPROMs. If that doesn't work try swapping the EPROMs from your working board.
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
Other things to try:
1) raise / lower voltage in case you have a voltage-sensitive component.
2) check the board for damaged / scratched tracks and test for continuity.
3) swap RAM chips for known workers if socketed.
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
I've posted the PROM chips off to you. I used 54s287's (higher spec version of 74s287 and equivalent to Harris 7611 and TBP24S10).
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
My trusty old Dataman Omni Pro II. It uses DOS-based software and an ISA card so I have to keep an old Windows 98 PC running so I can use it.
smiley36.gif
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Hi Gary,

the chips arrived today and I installed them and they work just great
smiley32.gif
.

Thanks for everything and I've made a donation
smiley20.gif


Wow, my points have gone up!jonhughes2014-05-20 20:23:00
 
Top