Power Supply Problem

Woodstock

Newbie
Credits
6CR
Hi,

I'm hoping someone might be able to help me with this problem please.

I have got an old Jamma cab that is running a PSU called a "Hantarex switched mode power supply US250". It has always run my current two PCB boards (Double Dragon 1&2) no problems. Recently I bought an R-Type bootlet PCB and although it runs, there are a few small problems (such as the background doesn't appear when you are playing the game and hence, you crash your ship all of the time by running into things you can't see).

It has been suggested to me that a bootleg PCB requires slightly more voltage, say 5.1 or 5.2v.

I'm finally getting to the question now: My power supply has an adjustment on the top but it is already set to max and won't go any further and is only kicking out 4.9v.

Should it be possible to adjust it up a bit more?

Does anyone have experience of a bootleg pcb requiring more voltage to run?

Does the fault I described with R-Type seem likely to be a voltage issue?

Thanks in advance for any advice!

Woodstock
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
It sounds to me like the caps inside the psu are failing so a meter measures 4.9v but its a very ripply supply and that could be whats causing your troubles, those psu's are at the age where there having troubles now
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
when they where new they where solid

but now the Hanty Series USXXX PSU are really unstable unless you rebuild them and replace failing components

i long got rid of all mine for ISOs and Switchers

change the caps as suggested and then take it from there

and yes the POT is to adjust the 5V line
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
it is just a case of replacing all the capacitors inside, carefully....

then when I used to do them I would test them on a near full load

IMG_4022.JPG
 

Woodstock

Newbie
Credits
6CR
Thanks for the quick replies!

I'm happy to have a go at replacing the capacitors. I don't suppose there is a goo "how to" kicking around? :) Also, I assume it makes sense financially? I have no idea at this stage how many capacitors will be required and how much they cost compared to a new PSU.

BTW, you are going to laugh your socks off now but I assume the capacitors in the photo above are the tall cylindrical items? (Spot the newbie!) :)

Thanks!
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
yeah you got it, there are quite a few to do in those psu's, but does make them solid, use higher temperature capacitors 105 degrees C (I think they was fitted with 85 deg C but cant remember now) make sure you know which way round the + and - is and change them one at time, higher voltage capacitor are fine, just the value needs to be the same and of course size wise they need to fit.
 

Woodstock

Newbie
Credits
6CR
Hi,

I have removed the PSU and had a look inside. The caps are already 105 deg C versions and look kinda new, maybe they have been done before? Also, I read that if they were failing that they might be bulging but I can't see any evidence of this. Any thoughts?

PSU_caps.jpg
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
they dont have to bulge and those are defo original non replaced caps

Bulging capacitors are a Sign of catastrophic failure due to something more Sinister and would require further investigation than just a cap change

Normal Looking cxab of age are just caps that have started to die down and get old and at end of life

Leaky caps are a B**itch and could potentially cause alot more damage than one would want (they can corrode away the pcb and its traces

hanty always used the same style caps and those look familiar with hanty chassis original caps

the main failing point on caps is a lower capacity and higher ESR (Electro Static Resistance) ESR is the important thing here

any ESR over 1 Ohm is no good
Anything bellow that is recommended to change
anything around the 0.1 Ohm range or lower is ok

silverfox07862016-04-04 17:52:08
 

Woodstock

Newbie
Credits
6CR
Ah ok, thanks will look to replace all capacitors. BTW, where would you guys normally buy them from? Also, just posted a pic of the whole PSU as there is a "monster" capacitor just left of the centre (it has a green circular sticker on the top of it), it says 400v 330 micro Farads on it, I assume this needs to be replaced as well?

Full_PSU.jpg
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Isn't there a safety precaution about one of the caps on there, I can't find the message but i'm sure Mitchell Gant told me to stay clear of one of them. Whats a good way to discharge the big one for safety?
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Yes you can probably guess which one you need to stay clear of
until it's discharged (the big one). [Does it say 330 micro F or uF or

mF? I ask because it looks physically a bit big for only 330uF]

You can put an insulated screw driver across the pins of the

big cap if you don't mind some serious sparking. For a one-off

cap-discharge that is probably ok.

Personally I'd discharge through a high power, high Ohm resistor (like

I would a vector monitor or I'd use a high voltage probe if I had one).

Hunt down some vector monitor discharge threads for details on this.

Edit: Here's a thread. I use the screwdriver-wire-resistor(s)-crocclip method

http://www.ukvac.com/forum/hv-discharge-probe_topic347879.html

Battlezone2016-04-05 00:40:35
 

Woodstock

Newbie
Credits
6CR
Hi, The big cap says 330 uf(M) on it. I have done some reading on the internet but still a little stuck on what the (M) means...

BTW, I found a loose component on the PSU board, so I will also resolder that in. (circled in red below).

Full_PSU_and_loose_component.jpg
 

Woodstock

Newbie
Credits
6CR
Hi,

Just as an update. Finally had an evening free to work on the PSU. I resoldered in the loose ceramic resistor and removed all of the caps as shown in a photo earlier in the thread. As I have a multimeter that has a setting for measuring capacitors, I measured them all but they are all pretty much on the money. for example: 2200uf cap coming in at 2254uf when measured & 100uf cap coming in at 98.5uf. The worst one that I found was 2200uf cap that measured at 2089 & another 2200uf cap that measured at 2395uf. Which are all within the +/- 10% rule of thumb as being ok.

So, does this mean the caps are ok or am I missing something?

Thanks for any comments!
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
no, replace them anyway, there 25 years old!! they dry up, and unless you measure the ESR of the capacitor as well it is not a good indication if it is ok, you can have a capacitor that measures spot on, but if the esr is 20r (effective series resistance) it won't smooth the ripple which you would THINK it would as the capacitance is spot on!

But mainly there 25 years old, change them...
 
Top