Midi cab plans

muddymusic

The Repro Guy. Art and Parts supplier
Staff member
vacBacker
Feedback
52 (100%)
Credits
2,271CR
I decided it was easier to measure everything I could, that way you can see how it all fits together.

This is a Taitel T-83 cabaret. Overall cab size is 550mm wide. The neckboard is a few cm from the back door and the chassis is mounted on the side of the cabinet. It wouldn't fit with the cage on.

Taitel_side.jpg


Taitel_rear.jpg


Taitel_front.jpg


Taitel_monitor_bezel.jpg


Monitor wood measurements.
Taitel_monitor.jpg
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
Cheers man. Wish I'd seen that before, its practically what I've ended up with anyway!

Will adjust accordingly, I don't want an exact clone but that gives me enough to work with.
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
Many thanks for the dimensions so far. Design is coming along. Looking a bit more like a classic Australian style lowboy cab. I've made the marquee section nowhere near as deep as the Taitel because the cab height is significantly shorter.

minicabwireframe.png


Other than the sides where it's not so important, everything is exact millimetres, and I've tried to round to the nearest 5mm everywhere. All done with no mitres so getting the plans CNCed should be a doddle.

It should fit a 20" Hantarex Polo or similar horizontally or vertically.

Need to do a bit more checking and add holes for the usual stuff, then go over it and place all the dowels.

Contemplating doing it with a flat top. The benefit being you can shove stuff on top of the cab. The downside being the marquee is then perpendicular to the ground unless some parts are mitred. Not sure right now.
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
Nope, although I do get to wear that hat when it suits.

I just made a list of all the bits I liked in different cabs and appropriate properties and put them together :)

Hoping I'll finish this soon so I can prototype it.
 

urbanledge

Active member
Feedback
2 (100%)
Credits
95CR
cools said:
no mitres at all. Not sure exactly how well some of the joins between panels will work

Have you ever heard of a kreg gig?

Its the absolute dogs bollix if you can get it predrilled and use the correct screws for the timber.

unbelievably strong join at 90 degrees with no glue/battons.

They look like this

detail.jpg


You use a machine to drill the hole then drive the screw home.

urbanledge2014-04-24 08:09:28
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
There are no joins like that. I'm referring to the non 90 degree angles that give the cab its shape, like where the roof meets the back.
 

urbanledge

Active member
Feedback
2 (100%)
Credits
95CR
You could use them to fix every thing onto the gables
then worry about the non 90s at the end.

I'm using the gig system on my current build and will never do woodwook with out them again I reckon!
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
I'll stick with dowels methinks, bit more idiot proof for sending plans off for cutting.

Got most of the detail and internal work done. I'm not sure I'm entirely pleased with having a flat top, I may try angling the sides whilst keeping the marquee area flat and see how that works.

minicab3.png
minicab4.png


EDIT: better

minicab5.png
 

Milky

Moderator
Staff member
vacBacker
Feedback
16 (100%)
Credits
1,037CR
cools said:
I'm not sure I'm entirely pleased with having a flat top, I may try angling the sides whilst keeping the marquee area flat and see how that works.

I quite liked the sloped top, it looked very cool - if its just from a storage perspective, you could just pop a shelf up above where the cab will sit?
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
Yeah, I might try reverting that part. Think I'll keep the lip at the back though, I quite like the idea of not losing stuff down the back of the cab.
 

Milky

Moderator
Staff member
vacBacker
Feedback
16 (100%)
Credits
1,037CR
cools said:
Yeah, I might try reverting that part. Think I'll keep the lip at the back though, I quite like the idea of not losing stuff down the back of the cab.

Yeah, that's an important addition to avoid the awkward "aargh! my car keys!!!" moment
smiley36.gif
 

Beaps

Active member
Feedback
11 (100%)
Credits
364CR
cools said:
Just picked up a brand new in box HP s9500 19" PC CRT to decase for this. :D

Loving this tread....

So you going with a PC monitor, would you still be able to run it in low res to get scanlines or are you not fussed?
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
It'd be an emulation cab so fake scanlines (or real hardware scanlines running at double frequencies).

As it's a CRT if you just run at a doubled resolution with fake scanlines it looks authentic, albeit a tad crisp on a monitor that's capable of clear 1600x1200 natively.

Tabletops with LCDs rather than small PC CRTs in I don't understand at all - the CRT would look infinitely better and have perfect viewing angles...
 

ZedEx48K

8-Bit
Feedback
2 (100%)
Credits
1,424CR
cools said:
As it's a CRT if you just run at a doubled resolution with fake scanlines it looks authentic, albeit a tad crisp on a monitor that's capable of clear 1600x1200 natively.

There's a pretty easy way to cure that and soften the image with pc monitors though*, take the back off and there's 3 pots on the lopt, brightness and H & V alignment, just offset the last two a little till you are happy
smiley4.gif


* Not my fault if you kill the monitor or yourself
smiley36.gif

ZedEx48K2014-04-28 16:46:14
 

cools

I joined ages ago honest
Feedback
19 (95%)
Credits
799CR
Defocussing the horizontal might be an idea, I didn't know PC monitors had a separate H and V focus. Definitely don't want to defocus the vertical though, that'd mess up the scanlining ;)
 
Top