MTC9000 help

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
I'd really aappreciate it if you can tell me which ones I can solder back on, based on the out of circuit tests above?

I assume TR20, 21, 22 are ok?

No idea for TR17 and TR 19?

TR15 replace?

Purity2014-01-15 18:38:25
 

pulstar

Active member
Feedback
41 (100%)
Credits
459CR
Purity said:
I'd really aappreciate it if you can tell me which ones I can solder back on, based on the out of circuit tests above?

I assume TR20, 21, 22 are ok?

No idea for TR17 and TR 19?

TR15 replace?

Pretty much this. TR15 is definitely bad from the results you've got. The rest seem OK. TR17 & TR19 are pretty hard to test (or at least I'm not sure what results to expect).
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
I've just noticed that I took TR18 out instead of TR19
smiley9.gif


Two
questions. Should TR18 be bridged like this? It was already like this
when I desoldered it and I've put it back exactly the same way:

IMG_0213.jpg


Also where the hell is TR19?? I cannot find it anywhere on the layout diagrams? Am I being blind here?
 

pulstar

Active member
Feedback
41 (100%)
Credits
459CR
TR19 is right next to TR22. On the layout diagram there is TR22 and ZD2 coming back towards the LOPT, to the right, next to R111, is TR19. Not sure about those points being bridged, my instinct says no but I can't confirm. I'm sure Ordyne will be able to give you a definitive answer as to what is correct.
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Yup, I just had another look at the chassis and found TR19(BU801). I took it out of circuit and read the legs as BCE:

B+ C- = .069
C+ B- = 0.71
B+ E- = 1.007
E+ B- = .883
E+ C- = .805
C- E+ = .952

So that looks screwed?
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
You need to look at what they are, BU801 is a Darlington like the bdx53 so its essentially two transistors in one package, hence your readings. I'd put it back, its not shorted.

I personally wouldn't have pulled every transistor in the psu section, the two likely culprits of your dead short were the hot and tr20
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
I've soldered the transistors back on and replaced the HOT. Powered on with the scan coil connector unplugged, and am getting a reading of 183v at SP3 and 178v at SP4 approx. No fuses have blown.

I've not tried this with the scan coil re-connected yet

Any advice on what to do next?
Purity2014-01-23 20:42:39
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Ok, so with yoke disconnected you've got no fuses blowing and 183v at sp3 and 178v at sp4 - looks like its time to load test the psu section.

What I always do here is add something that can draw current across the regulator circuit - for this purpose I got taught to use a 40 or 60w standard lightbulb (not the econocrud) connect one end to sp4 and the other to frame and power up - without the yoke connected.

You should now get 130v at sp4 - you'll have to rig a bit of a convoluted setup to put the lamp and meter on there at same time. I built a little test rig for it.

If you're getting 128-132 there with a load well then its time to go for broke and plug the yoke back in.

This might be an unnecessary step for some people, I just like to prove that part of the circuit before going onwards.
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Your b+ is bang on for no load, personally I'd lift one end of d10, plug the scan coil connector back in and power up to see if it runs.

I'd only use the light bulb to test for a psu fault, that doesn't seem the case and is extremely rare to see a load related fault on a 9000, plus you've had most of the silicon out and tested it already!
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Ordyne said:
Your b+ is bang on for no load, personally I'd lift one end of d10, plug the scan coil connector back in and power up to see if it runs.

I'd only use the light bulb to test for a psu fault, that doesn't seem the case and is extremely rare to see a load related fault on a 9000, plus you've had most of the silicon out and tested it already!

Hehe, i'm just a bit belt & braces and double cautious. Prove twice, blow up once
smiley1.gif


I really want it to be plug & go for Ben at this point Craig, I wish when mine went black screen they were only a few silicons to change.

I take it the lift d10 is to ensure that over volt protection doesn't kick in and cause red-herrings?
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Cheers guys. Thanks for the advice.

The way I see it, the chassis was not working when I started to look at it, so I'm inclined to plug it in with D10 lifted...but stand back :)

I'll probably do this at the weekend and let you know how it goes
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Unfortunately it didn't go too well :-(

I lifted a leg of D10, powered on the monitor, and I can hear what I would describe as a hissing noise or zzzzzzz noise, that seems to be getting louder and is coming from the chassis. There was no smoke or anything visually I could see.

I didn't notice any neck glow from the monitor

smiley19.gif


Purity2014-01-26 15:20:38
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Is the monitor still in the cabinet? It would be nice to locate where the noise is coming from!

I'd check to see if the wire wound resistor on e side of the chassis is getting toasty.
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
I replaced C53 with another 400uf 200v cap

Powered on with D10 disabled and I am getting neck glow now
smiley20.gif
.

Turning up the focus and brightness to about half way on the LOPT and I am getting a stable image on screen, although I have not put any signal through it yet

The zzzzz or hissing noise is still happening, and seems to be coming from the neck of the tube rather than the chassis

Purity2014-02-01 15:46:59
 
Top