Tech help: Bubble Bobble PCB

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Hello everyone,

I'm trying to get a Taito BB board working fully and I'm running into some difficulty. Can anyone shed any light on these issues:

1. Sound

I'm getting no sound and figured out (well P-Man advised) I need -5V. This is supplied by my cabinet PSU but not by my harness. I've added this voltage, but whenever it's applied I get a lot of interference/wavy lines on the screen - looks rather like a grounding problem. Do I need additional grounding for the -5V supply?

I haven't yet checked whether I'm getting sound or that the PSU can supply the necessary current. I was stopped in my tracks by the failure to get free play (2) and no coins!!

2. Freeplay

I can't find a free play setting. The Romstar manual mentions the fact you can run without a coin meter by bridging a jumper at jp7. I tried this to no effect, but the jumper configuration is a bit odd with 3 spots - I may have bridged the wrong direction:

x

xx

Has anyone had one of these boards on free play?

After battling the blasted area51 cab for ages, the last thing I wanted was to be fannying about with a board that should have just been able to slot into a jamma harness and go (it has a hard wired adapter)

HELP!! :)

thanks

stu

gridrunner2011-03-10 09:58:13
 

andyman

always pull away from your face
Credits
1,059CR
No additional GND needed, also not much current required on -5v so unless you're getting nothing, suspect elsewhere. BB has no freeplay and running without a coin meter is just a counter so won't help.

Its either coins or a switch to gnd from pin 8 on the harness

Andy.
 

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Hi Guys,

OK, there's no sound with or without -5V. With -5V applied, the screen suffers alot from what looks like grounding interference patterns, wavy lines, white noise. With it removed, the screen is fine.

I've checked the volume control but no effect.

I'm still not certain the-5V is needed. The Romstar manual only mentions it in the context of coin door lamps and the manual appears spot on as it references the board 100% accurately, in detail. It claims you only need +5 and +12 from your PSU.

http://bubblebobblehq.110mb.com/bubblebobble/arcade/bb_us_manual.pdf

Stu
 

paulcan69

Can reburn OTP EPROMs! Fear my power!
Feedback
11 (100%)
Credits
945CR
In your cab is video gnd also bridged across to normal gnd?

I've had a couple of cabs do that and all I had to do was add a jumper wire from video gnd on the jamma harness and connect it to GND.

Good luck, sound section sorry haven't a clue.

smiley17.gif
(I'm not the person to ask about that, much more experience on here that me)
 

paulcan69

Can reburn OTP EPROMs! Fear my power!
Feedback
11 (100%)
Credits
945CR
Also I think you do need -5v as it's on the H connector which all needs to be connected, I'm sure you do need this on a Bubble Bobble original, mines connected and has no issues?
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
IF anyone has encountered any Bubble Bobble sound issues please can they respond to this thread :)

Gridrunner got the pcb off me and the sound worked fine on my test rig and i'm sure the pcb is still fine and there's some harness issues going on somewhere.
 

andyman

always pull away from your face
Credits
1,059CR
Definitely -5v connected to pin 8 on the H connector ?

TL074 op amp requires -5v btw, it may be the source of your problem

Andy.
 
G

Guests

Guest
Bubble bobble Definitely needs -5v or you will get no sound.
 

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Hi Guys,

I'm pretty confident this is a harness issue now. I had a look at the harness against the Jamma and BB pin outs and things look most definitely amiss with the speaker wiring. It's the only part of the adapter end of the harness to be hand soldered without sheething. I haven't brought my tools today, so I'm planning to test things and make a fix at the weekend (the machine is in a gamesroom), so this was just a visual inspection.

What I'm seeing is what I think are the speaker wires coming in on pins J/8 (white and blue). These are neatly sheethed so it's been done by design. Pin L/10 has some hand soldering wiring that doesn't appear to be going to the speakers but somewhere else, possibly switches on the CP?

The game otherwise plays fine, so the video and game controls, as well as the power, all appear to be fine, apart from the missing -5V.

This was supposed to be a Jamma cab, although I haven't used it before. It used to be home to a Tekken 4 and the loom has been hacked about a bit.

Can anyone think why the speaker wires would come in on these pins?

thanks

stu

gridrunner2011-03-11 12:39:27
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
Glad you believe you've found the issue. I may have a NOS JAMMA harness somewhere if you fancy rewiring the whole cab!
 
G

Guests

Guest
Alpha1 said:
Glad you believe you've found the issue. I may have a NOS JAMMA harness somewhere if you fancy rewiring the whole cab!

if you are unsure about the harness in your cab, this would be an ideal thing to do, if oll cant help you, you can get complete jamma looms of ebay for about £20~
 

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Hello chaps,

a problem with the harness meant that the -5V was shorting to ground when connected. On clearing the short and applying -5V, the screen interference went, I can hear the pot scratches through the speakers as I move the volume pot around and the pop as it's switched on, but there's no sound.

I'm assuming I've frigged the op amp on the board with this short?

thanks

stu
 

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Crap was my reaction x 10. The wire for -5V had come free from the hacked harness on the board. I've clearly re-attached it in the wrong place, as I doubt it was deliberate routing it to Jamma ground!

The amp is a quid part, so I'll swap it using a socketed equivalent in case i screw it up again. I just hope there isn't any more damage. What else would use that -5V rail?

thanks

gridrunner2011-03-13 18:05:44
 

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Hi dude,

Good to see you've found a likely cause. I'd have a good think about using a socket for the op-amp though. Due to the incredibly small magnitude of the signals in use I've found that some circuits end up being quite noisy just by having the op-amp socketed. I'd say it's a pretty safe bet that you've popped it, and replacing it even if it's not the only fault isn't an issue so I'd say solder in direct. It's not a NLA component (No Longer Available) so by chopping it out and swapping it you're not unnecessarily depleting stocks of any key parts so I tend to be a bit more ruthless when working with ICs that fit that criteria.

Just IMO though - others might have contradictory experience.

Also, is it definitely just the op-amp which uses the negative rail? I seem to recall that the reddy-brown SIL custom also used it - maybe AnDyC will know as I know he modded a board to not use the SIL. I'd grab the schems but my internet is doing the standard Virgin sunday-slowdown
smiley19.gif
and getting this page to load was pretty painful.

Anyway, good luck and I'm sure it'll be back working in no time at all.
 

gridrunner

Ex-lurker!
Feedback
3 (100%)
Credits
206CR
Cheers guys. I'm hoping any damage is confined to the audio section. Every other aspect of the game plays fine, so that at least is a good sign. I'll swap the amp next. If anyone has any further thoughts on what else might be affected do let me know. Ta.
 

andyman

always pull away from your face
Credits
1,059CR
trm said:
Also, is it definitely just the op-amp which uses the negative rail? I
seem to recall that the reddy-brown SIL custom also used it

You are quite right, I thought it was just the amp
smiley9.gif


Andy.
 
Top